air box removal

Forhan, Thomas Thomas.Forhan at mail.house.gov
Wed May 8 14:46:21 EDT 2002


This message is in MIME format. Since your mail reader does not understand
this format, some or all of this message may not be legible.
--
[ Picked text/plain from multipart/alternative ]
George, I did this job a couple of years back. As I posted as a comment on
Chris Millers' great pages http://members.aol.com/c1j1miller/main.html :

The Bentley has -on page 87.18, what appears to be detailed instructions on
removing the heater box. What stopped my was when I came to the line "Remove
all retainers between the body and heater." What does that mean? Why did I
take out the center console. What to do now?
1) Look at the picture on 87.22. From the interior, remove the two footwell
air outlets (two screws each). After disconnecting any vacuum lines that
might be clamped to them, remove the two large elbows on either side of the
vacuum servos- they pull down, and a little out. No screws involved. Remove
the corrogated rubber duct connection that is up closer to the firewall. I
did not need to remove any other ducting.
2) Look at the picture on 87.28. Disconnect the three vacuum lines -yellow,
blue and green- from the vacuum servos. Disconnect the red, black and white
lines at the joints located right next to the vacuum servos. (No need to
remove the two vacuum servos)
3) Back on top in the engine compartment, disconnect the red, black and
white vacuum lines located on the passenger side of the heater box .
Disconnected top and bottom, a section of these three lines will come out
with the heaterbox. Notice the metal A/C line running left to right in front
of the airbox. Cut any cable clamps from it and move flexible wires and
lines out of the way. There is very little clearance between the A/C line
and the heater box as you later pull, push and rotate the box out.
4) Use a narrow (like 1") thin bladed, flexible putty knife to break the
seal between the box and the firewall where you have access ( primarily at
the top of the box, and the drivers side. Next, carefully use a thick
bladed, ridgid 1" putty kniffe to begin to pry the box away from the
firewall. Follow up with a big flat bladed screwdriver. At this point, I had
about an inch of motion on the upper drivers side of the box. Push the
bellows A/C duct connector on the passenger side into the heaterbox, I taped
it back so it would not interfer. Keep working it. I spent a lot of time
laying on top of the engine, arms reaching around both sides of the box,
gradually pulling. Slowly, the adhesives would release. Finally, the box was
loose all around.
(Next you need a helper. Word to the wise: if your helper has a strong
emotional attachment to the car and has not been following your progress,
warn him or her about what they are about to see. Its not a pretty picture.
Your helper will look at the mess in the interior and not realize that you
labled all the wires and switches with masking tape, tucked the screws and
bolts into labled baggies, and of course have the Bentley, Chris' pages, and
all your buddies on the list to help figure out how to put it back together.
My wife is convinced I have managed to turn our car into junk that would
have to be towed away.)
5) Have the helper push from the interior, more or less on the vacuum
servos. The need to be pushing up and forward- at about a 45 degree angle.
Meanwhile, assume a position laying on top of the engine, hands grasping
either side of the airbox. pull back and up, favoring the passenger side.
When you have clearance, remove the black bellows connection to the A/C
unit, and push the airbox back down a bit. Then start pulling up favoring
the drivers side, until the box clears the metal A/C line. Now a big push
from below while you lift and rotate the top of the airbox back a little.

Disassembly of the heater box is not tricky, but I had to go buy something
like a long 14" blade Phillips to get to one of the screw holding it all
together. Take lots of pictures and make sure you see what is going on with
the various servos etc. Assembly is tricky because you have to get the
various flaps in the right place. I had one side of the box on the
workbench, inserted all the flaps and parts, and then glued some fishingline
to the top end  of the flaps, and threaded the line through the appropriate
holes in the upper half of the box, so that I could slide the top half onto
the bottom and get all the flaps into the right place. The last two
sentences will make no sense to you at all until you have the box apart.
:-).

Good luck, once into it feel free to email me directly for advice.
Tom F.



More information about the 200q20v mailing list