[Es2] That Evens stuff, was things that tend to break...

Bernie Benz b.benz at charter.net
Sun Jun 18 14:44:53 EDT 2006



> From: "Mark Wetzel" <mark.wetzel at verizon.net>
> 
> Actually I run straight distilled water with Water Wetter. I don't run ANY
> coolant mixture.
Right on for max heat transfer, Mark! What do you do for corrosion
protection? If you have any iron block rust in the system it is easily
removed by adding a little oxalic acid to a water flush and run it for a few
hours or a day. Dissolves only iron oxide, harms nothing else. Readily
available at any paint store as ³wood bleach².

Regards,

Bernie Benz
Gardnerville, NV

'90 90Q-20V  165K
'91 200Q-20V 215K
¹02 A6 2.7TQ 6spdMT 75K
'88 Ford "Quatro" Tractor
Other Misc. Toys 

> 
> Every product has a splashy website or other advertising glossy. Everyone's
> product is the best thing since sliced bread.
> 
> Whatever the case, I've tried many different blends and products, and via
> actual testing this is the best thing in my car. This keeps my water temps
> cooler by about 5-7 deg C and my oil temp around 7-9 deg C cooler. I've run
> mixtures from 50:50 down to 10:90, Ethylene Glycol:water.
> 
> I've just started testing the Evans coolant and with the hottest part of
> summer coming up soon, I should have some real world data soon.
> 
> Regards,
> Mark
> M.Wetzel's Racing Products LLC
> 
> -----Original Message-----
> From: Bernie Benz [mailto:b.benz at charter.net]
> Sent: Sunday, June 18, 2006 1:01 AM
> To: Mark Wetzel; Brandon Hull
> Cc: es2 at audifans.com
> Subject: Re: [Es2] That Evens stuff, was things that tend to break...
> 
> 
> Mark, thanks for your response and the link. Understanding that you are
> trying to repeat your understanding of the Evens coolant, and not wanting to
> put you down at all, only this hype. IMO:
> 
> 1. Apparently the Evens is 100% PG, not an H2O mixture. Inasmuch as H2O has
> the highest specific heat of any substance on this planet, the heat transfer
> capabilities of PG are maybe half that of H20. Further, with its
> considerably higher viscosity the same pumping loop system will have a
> substantually lower flow rate. Both factors contributing to a lesser heat
> transfer from the engine.
> 
> 2. Cavitation is not a factor in heat transfer to the fluid. It does not
> exist on the wetted heat source surfaces. The surface coefficient of heat
> transfer from a source surface is greatly increased by turbulent rather than
> laminar flow across the surface, requiring the maximumizing of flow
> velocities and minimumizing of fluid viscosities.
> 
> 3. The vaporization of liquid in micro bubbles on the source surface further
> increases the heat transfer to the fluid. Inasmuch as H2O has the highest
> heat of vaporization of any fluid, it is again the best heat transfer fluid
> on the planet. Additives to H20 are necessary only for corrosion protection.
> Pressurization increases the boiling point of water to extend its heat
> transfer capabilities. When you want maximum cooling, use a mixture of only
> 10 or 20% EG.
> 
> Bernie
> 
>> From: "Mark Wetzel" <mark.wetzel at verizon.net>
>> Date: Sat, 17 Jun 2006 18:58:58 -0400
>> To: "Bernie Benz" <b.benz at charter.net>
>> Subject: RE: [Es2] things that tend to break
>> 
>> Evans is Propylene Glycol as opposed to Ethylene Glycol.
>> 
>> It's got a much  higher boiling point so there's no cavitation against the
>> cylinder walls, so there's better heat transfer.
>> 
>> It's not a new black magic potion, but it is more expensive therefore not
>> very popular.
>> 
>> http://www.evanscooling.com/index2.html
>> 
>> Regards,
>> Mark
>> M.Wetzel's Racing Products LLC
>> 
>> -----Original Message-----
>> From: es2-bounces at audifans.com [mailto:es2-bounces at audifans.com]On
>> Behalf Of Bernie Benz
>> Sent: Saturday, June 17, 2006 2:33 PM
>> To: es2 at audifans.com
>> Subject: Re: [Es2] things that tend to break
>> 
>> 
>> Hi Brandon,
>>> 
>>> -----Original Message-----
>>> From: es2-bounces at audifans.com [mailto:es2-bounces at audifans.com] On
>>> Behalf Of Brandon Hull
>>> Sent: Wednesday, June 07, 2006 3:53 PM
>>> Cc: es2 at audifans.com
>>> Subject: [Es2] things that tend to break on es2's at the track
>>> 
>>> Wow a thread with some life!  Well I once broke most everything from the
>>> cowl forward at the track but I guess that's not what you mean.  I never
>>> had cooling issues but from day one I ran Evans zero pressure coolant
>>> which I continue to think is a great idea in turbo engines, I don't know
>>> why everyone doesn't do it...
>> And just what is Evans zero pressure coolant?? Sounds flakey to me.
>> 
>>> I would guess the single most frequent contributor to
>>> artificially-shortened sessions in an I5 turbo is losing a hose.  So I'd
>>> emphasize fresh hoses, monster clamps, checked for tightness.   There is
>>> also a serious oil slosh problem although now I can't remember if it is
>>> long right handers or left handers that are the problem; but there is
>>> bad history here so don't overfill the oil and I wouldn't track it at
>>> all without the oilpan windage tray.
>> Hi G right turns slosh the oil to the left and out the breather system.
> The
>> windage tray may help on short duration turns but not on the long
> sweepers.
>> 
>> Bernie
>>> 
>>> Dunno how good you are at the track but absent adjustable anti-roll
>>> bars, you can have fun experimenting with tire pressures.  High rear
>>> pressures might get that pig to turn in and stay in long enough to wave
>>> to the apex.   In any event, the operative phrase is "trail brake"
>>> 
>>> Have fun, sure wish I was going!
>>> Brandon
>>> 
>> _______________________________________________
>> Es2 mailing list
>> Es2 at audifans.com
>> http://www.audifans.com/mailman/listinfo/es2


More information about the Es2 mailing list