[Marketplace] Parts: 1.8t stroker motor and 01E 6spd

[Jason Shaw]

Section:  Parts
Title:    1.8t stroker motor and 01E 6spd
Price:    3,850.00
Location: Colorado

Date:     December 05, 2012
Contact:  Jason Shaw
Email:    jasonshaw803 at yahoo.com
Phone:    224-430-9442

Description:
PICTURES.

For sale: Entire ready to build 1.8t stroker engine and 01E 6 speed transmission. I unfortunately do not have the money to finish this project, I am hurting for cash. The engine needs a good home :( . I Spent $4650 on all the parts and machining. Shes blue printed, balanced and ready to go. The engine is built for upwards of reliable 600+hp. All parts included to make it a crate engine other then the injectors and turbo charger. That all depends on how much power you want. NOT all the parts are in the Pictures. Its too much stuff. Everything includes:

-VW 2.0L ABA Block, bored to first oversize, milled deck, dowel pinned for head.
-1.8t AEB 20v head, complete rebuild, milled, dowel pinned to match 2.0L block, custom A/N oil fittings drilled into head to utilize center oil drains since the 2.0L block does not have them. Custom head gasket included.

-2.0L intermediate shaft, dowel pinned to pulley.
-Stock 1.8t cams, exhaust cam is dowel pinned to the cam pulley.
-Scat Rods 2.0L H-Beam rods rated for 800hp, weight matched.
-Custom JE 9.25:1 2.0L turbo pistons to match 1.8t head combo, side skirt coating and piston top high heat coating. Includes the heavy duty tool-steel 21mm wrist pins to match 2.0L H-Beam rods. Comes with the rings and clips.

-2.0L ABA Crankshaft, balanced, polished, crank pulley dowel pinned and flywheel dowel pinned.
-Stock 1.8t crank pulley, dowel pinned for crank.
-ARP Head studs
-ARP Main Studs
-Kolbenschmidt Rod bearings with Calico coating
-Techtonics tuning factory Audi/VW heavy-duty main bearings with Calico coating
-2.0FSI Coil conversion coil packs, connectors and pins included.
-Custom 1.8t oil pan, holds an extra quart of oil.
-1.8t AEB valve cover with drive by cable cam chain tensioner and/or new variable valve timing chain tensioner and new style valve cover if you are running an ME7 setup.

-XS power exhaust manifold cut and set for Borge Warner EFR turbo
-80mm Hemi V8 throttle body
-Custom large intake manifold, ran out of money to get it finished and welded up, I have all the parts you will need to mount it up to the 80mm throttle body though.

-Asco 1.8t aluminum super lightweight flywheel, dowel pinned for the crank and balanced to the crank.
-Febi Bilstein oil pump
-VDO boost gauge, for up to 30 psi
-Timing belt tension wheel from 16 valve euro turbo, this is the proper wheel for this combo.
-Proper timing belt
-All Gaskets included
-2.0L windage tray for oil pan

Most of everything is brand new. The 2.0L block mated to a 1.8t AEB head is a very potent combo!

This will include all the junkyard extras you may need. I have all kinds of timing belt covers as well as engine mounts for both the 1.8t AEB and 2.0L ABA. Hardware, hoses, and alternators if needed. Some of the basic mounting hardware is new as well.

I have almost all the receipts for this stuff too.

I am asking $3850 obo for everything listed above.


I also have an 01E 6 speed transmission for sale with 80k on it and the 2nd gear update. It comes with both cv axles, a bunch of different boots and different size shift linkages. Its in great condition. I am asking $1250 obo. Thanks guys.

URL:
http://www.audifans.com/marketplace/show.php?table=pm_audifans_Parts&id=21171

--
[  This is an automated message    ]
[  You are receiving this message  ]
[  because you signed up for the   ]
[  Marketplace email notification. ]