quick question, typ 89

Alan Pritchard alan.pritchard at rm-electrical.com
Tue Apr 12 10:27:53 EDT 2005


Well, I know my 90 has separate fuel and ignition units, not sure about
the 80. basically the 90 harness is really worse for wear, corroded
connectors, broken wire on the temp sensor, damaged screens, broken
plugs, would be nice to put a good condition loom in if they were
compatible.

Best Regards
Alan Pritchard 
Network Administrator 
R&M Electrical Group Limited 

Tel: +44 (0)23 8068 5668 
Mob: +44 (0)7870 164812
web: www.rm-electrical.com 


-----Original Message-----
From: Ben Swann [mailto:benswann at comcast.net] 
Sent: 12 April 2005 15:01
To: Alan Pritchard
Cc: quattro at audifans.com
Subject: RE: quick question, typ 89

Alan,

Yes, the M80 is also CIS E-3 and the major difference is that the 90 is
a
5cyl and 80 is a 4cyl in most cases.  In the M80 I pulled a engine
management harness and control unit - there was only one control unit.
In
the 87.5 the fuel and ignition units were separate.  They may have
integrated them in later versions.  There would of course be differnces
in
the control units for no. of cyl. particularly the ignition module, so I
don't know if they are directly plug compatable, even if the later
CIS-E3
consolodated the ignition and fuel into one control unit.

I did observe that most of the sensors were the same, but not recalling
specifics except of course the different distributors, but even these
use
the same hall sensor connector.

My bet would be that it would be easier to re-arrange some wires and add
a
few if need be than to install a different harness - I assume that is
really
what you are trying to do, but - what are you trying to do?

Ben

[Date: Tue, 12 Apr 2005 09:56:52 +0100
From: "Alan Pritchard" <alan.pritchard at rm-electrical.com>
Subject: RE: quick question, typ 89
To: <audi at humanspeakers.com>, <quattro at audifans.com>
Message-ID:
<89382C3250656449AD82DFB4AA47F3EC3AE16A at bdc-hq-1.rm-electrical.com>
Content-Type: text/plain; charset="us-ascii"

Thanks huw, I mean the loom which connects to all the sensors etc on the
engine itself....
I know the 90q is cis3
But not sure about the 80, I know it has a lot of the same hardware, I
guess the main difference would be if the 80 has a pot on the airflow
plate....
Ill look tonight. thx

Best Regards
Alan Pritchard
Network Administrator
R&M Electrical Group Limited

Tel: +44 (0)23 8068 5668
Mob: +44 (0)7870 164812
web: www.rm-electrical.com ]



-------------------------------------------------------
R&M Electrical Group Limited
-------------------------------------------------------

Message from: Alan Pritchard
Message to: Ben Swann
Date: 12/4/2005

This message (and any associated files) is intended only for the use 
of the individual or entity to which it is addressed and may contain
 information that is confidential, subject to copyright or constitutes a 
trade secret. If you are not the intended recipient you are hereby 
notified that any dissemination, copying or distribution of this message, 
or files associated with this message, is strictly prohibited. If you have 
received this message in error, please notify us immediately by replying 
to the message and deleting it from your computer. Messages sent to 
and from us may be monitored. 

Internet communications cannot be guaranteed to be secure or error
free as information could be intercepted, corrupted, lost, destroyed, 
arrive late or incomplete, or contain viruses. Therefore, we do not 
accept responsibility for any errors or omissions that are present in this
 message, or any attachment, that have arisen as a result of e-mail 
transmission. If verification is required, please request a hard-copy 
version. Any views or opinions presented are solely those of the author 
and do not necessarily represent those of the company. 




More information about the quattro mailing list