[s-cars] Connectors cover in FA and looking for a parting car

Tom Green trgreen at comcast.net
Sun Apr 4 13:23:20 EDT 2004


> Previously, on Sat, 03 Apr 2004, Kirby Smith added:

> On my '95 S6, the "belly cover" is retained by tabs on the bumper  
> cover,
> two front fasteners, four side fasteners, and three rear fasteners.
>
> kirby

> Vincent Frégeac wrote:
>>
>> Thanks for the link about the connectors cover. But the sound deadener
>> in the link you sent looks like the one I found in the FA but not  
>> what I
>> have on my car. On my S6, the sound dampener is a large single piece  
>> of
>> plastic with two metallic fasteners on the lower part and four plastic
>> fasteners on the sides. I need one of the metallic fastener and three  
>> of
>> the plastic ones. A bit scary, I have to admit.
>>
>> Vincent.
>>
>> -----Message d'origine-----
>> De : bob.rossato at att.net [mailto:bob.rossato at att.net]
>> Envoyé : 3 avr. 2004 17:21
>> À : Vincent Frégeac
>> Cc : s-car-list at audifans.com
>> Objet : Re: [s-cars] Connectors cover in FA and looking for a parting
>> car
>>
>> Vincent wrote:
>>> Spring is coming and I try to make a list of all the small plastic
>>> broken parts I’ve been too lazy to replace, like a connectors cover
>>> fastener. I’ve found most of them in the FA but I can’t find the
>>> connectors cover on the firewall in the FA to determine if the  
>>> fastner
>>> have a specific P/N.
>>
>> Item # 36 here:
>> http://www.elcats.ru/audivw/vag5.asp?subm=%CF%EE%E8%F1%EA&btsnr=971- 
>> 52&c
>> id=155
>>
>> And then Vincent added:
>>> Going further in the list of small tid’n buts, there is a few other
>> P/N
>>> I would need:
>>> - the plastic fastener for the sound deadener (belly pan)
>>> - the rubber washers which avoid these fastener to fall from the  
>>> belly
>>> pan.
>>> - the bracket these fasteners goes into.
>>
>> See here:
>> http://www.elcats.ru/audivw/vag5.asp?subm=%CF%EE%E8%F1%EA&btsnr=863- 
>> 25&c
>> id=155
>>
>> ...though for some reason it doesn't show the two front screws.  And  
>> the
>> five dzus fasteners (3 rear, 2 front) are metal.  It's the ones in the
>> fender liners that are plastic.
>>
>> Bob

Vincent,
The illustration in the FA  shows the additional panels for the diesel  
engine.  The AAN application only uses the front panel shown, and  
indeed has 5 metal fasteners and 4 plastic fasteners. I don't know what  
happened to the front two in the FA, but you really do need them.   
There was a change in '95 from the metal fasteners shown in the  
illustration with the 1/4 turn speed screw with separate metal washer  
to a speed screw with integral washer on head.  The  dzus receptacle is  
also changed so new style fasteners will require new receptacle clips  
also.  The notation under the part description F>> 4A-S- 100 001*  
indicates after serial number...
My numbers are 4A0-805-121 (PIN), 8D0-805-960 ( SPEED NUT),and  
4A0-805-137 (RETAINER WASHER).
You will also notice on the Ru etka that both speed nuts have the same  
part no. for 10 and (10) for both sides of the break in vehicle serial  
number but they are physically different in size. The new pins are  
larger and will not go in the smaller hole of the older speed nut clip.
I can probably match up a set (no rubber retainer washers) or two of  
old ones, but you need to look for where you are missing fasteners to  
determine how many you really need and if your pins have separate metal  
washers under the head.  Yeah, one fastener is scary !
I am unsure of the plastic pin and retainer part numbers.

Tom '95 S6



More information about the S-CAR-List mailing list