[s-cars] Boost leak - update, what am I missing here?

[Theodore Chen]

it's still a possibility.  i wonder if you could loosen some bolts
and allow exhaust to bypass the cats (just temporarily, for testing
purposes) to see if the boost comes back.

-teddy

--- Mike Claire <mike.claire at gmail.com> wrote:

> Steve Mills suggested clogged cats.  I sure hope not - my Stromung cat-back
> has less than 30K on it, and I keep the car running right.  I doubt I've
> overheated or otherwise ruined them.
> 
> 
> 
> Mike
> 
> On 4/21/07, Steve Mills <s.b.mills at gmail.com> wrote:
> >
> > Mike-
> >
> >    Could also be clogged cats. When I bought it my 92 wouldn't make more
> > than 1.4 BAR and even getting to that was paiiinnfulllllyyyyy
> > ssssllloooowwwww. The PO chased what he thought was a boost leak and then a
> > turbo problem for 6-8 months (new turbo, full Samcos, many $$$) and it was
> > just clogged cats the whole time.
> >
> >   Cut off everything back of the turbo, install Stromung, whee haaaaa!  I
> > can now peg it at 2.1 (on the factory gauge) at will.
> >
> >    HTH-
> >
> >    Steve
> >
> > On 4/21/07, Mike Claire <mike.claire at gmail.com> wrote:
> >
> > > A bunch of you guys replied to me last week with ideas, and I appreciate
> > > the
> > > help.  I've gone through everything suggested, and have read everything
> > > about these issues I could find on Scott Mockrey's site,and STFA with
> > > abandon.  I'm pretty much tapped - nothing to show for it.  I was
> > > distracted
> > > this week by new symptoms - and ultimately #3 coil just failed entirely.
> > > Dead short.  That's fixed now and the car runs great again - except it's
> > >
> > > still low on boost.
> > >
> > > (subject is a '93 S4, MTM 1+ (Pastore) chip.  Used to indicate 22 lbs on
> > > A-pillar gauge.  Now it peaks at 16 or 17, and backs down from there.)
> > >
> > > I'm either losing boost - or not making enough of it.  I don't know
> > > where
> > > else to look - what am I missing here?
> > >
> > > 1.  Pressure tested main intake plenum to 15 lbs with a compressor and
> > > PVC
> > > cleanout plugged into the intake boost.  Closed off Samco where it
> > > enters
> > > the intake, and the ISV - PASSED
> > >
> > > 2.  Pressure tested all the small hoses in the PCV circuit, water trap,
> > > ECU
> > > connection, boost gauge connection, etc. etc.  PASSED
> > >
> > > 3.  Removed BPV, plugged the Samco, plugged vacuum line (eliminate
> > > possibility of BPV leaking pressure).   PASSED
> > >
> > > 4.  Removed silicone line from wastegate, plugged it shut (to test for
> > > possibility of wastegate opening prematurely)  PASSED
> > >
> > > I can only think of two possibilities - either the turbo is no longer
> > > capable of building normal boost, or the intake plenum is leaking at
> > > pressures higher than 15 lbs.
> > >
> > > Could the turbo be failing?  It sounds the same and drives the same as
> > > ever
> > >
> > >
> > > I can take the Samco off the turbo outlet and pressure test from there,
> > > but
> > > I don't have compressor plug handy for that.
> > >
> > >
> > > Before I do that - any ideas?
> > >
> > >
> > > Mike
> > > _______________________________________________
> > > S-CAR-List mailing list
> > > S-CAR-List at audifans.com
> > > http://www.audifans.com/mailman/listinfo/s-car-list
> > >
> >
> >
> _______________________________________________
> S-CAR-List mailing list
> S-CAR-List at audifans.com
> http://www.audifans.com/mailman/listinfo/s-car-list
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com