[s-cars] AC low side recharge adapter

[Young, Steve]

Having read these A/C posts with interest, I'll add my $0.02.  I will be
looking into my A/C system soon, as it provides no cooling.  So bear
with me as I have done no investigation to date.  If the low pressure
cutout switch is the type that screws onto a threaded schrader valve
port, any refrigeration supply house should have a tee fitting that
could be installed between the A/C line port and the cutout switch
leaving an additional port for gauge hookup.  This assumes that there is
physically enough room to add the tee, and then orient it so that a
gauge hose can be attached.  It also assumes that Audi did not use a
fitting with a non-standard thread.

http://www.grainger.com/Grainger/items/3GD02

An alternative would be the pick up a braise in port fitting and install
it in a manageable place on the low side of the system.  If you system
is already empty, this option will take about 30 minutes to install by
drilling the proper hole in the low side line, and braise in the
fitting.

http://www.grainger.com/Grainger/items/3X729

Or use something like this.

http://www.grainger.com/Grainger/items/3WU91

YMMV, and please verify the line size before purchasing.

Regards,

				TRANE
Steven Young
Local Operations Manager
Albany Office




-----Original Message-----
From: s-car-list-bounces at audifans.com
[mailto:s-car-list-bounces at audifans.com] On Behalf Of Tom Green
Sent: Tuesday, July 03, 2007 10:31 AM
To: s-car-list at audifans.com
Cc: calvin at earthlink.net
Subject: Re: [s-cars] AC low side recharge adapter

This issue has been revisited many times without any definitive answers
given to the list.  The most often asked is about adapting a gage set to
the low pressure port for a DIY recharge.  But no one has offered any
specific details for this even if they said " I did this myself".  Even
the local dealer service manager claims they never use the low pressure
port, only connect to the high pressure port at the condenser, evacuate
and refill a measured charge with the engine off, and measure the high
side pressure and interior duct temperature for any fine tuning of the
charge with the engine running at 2K rpm.  There is some risk of
introducing liquid refrigerant into the compressor by using the low side
port if you are not careful or overcharge the system even though shops
use this system on most vehicles, and of course, the high side pressure
will burst a DIY can and will only allow a recharge with the compressor
off.

My high side valve is on the front right side of the condenser and
easily accessible on the S6.  I don't know about the R12 systems on the
S4.

Is there someone on this list who can put these issues to rest?    
That is, can someone provide a source
for a low side adapter?  Does anyone have specific details of the
differences in the URS4 systems using
R12 and the URS4/6 systems using R134a?

Tom


> Date: Mon, 02 Jul 2007 21:24:49 -0400
> From: Kent McLean <kentmclean at comcast.net>
> Subject: Re: [s-cars] AC low side recharge adapter
> To: s-car-list <s-car-list at audifans.com>
> Message-ID: <4689A561.5060607 at comcast.net>
> Content-Type: text/plain; charset=ISO-8859-1
>
> Aaron Ryba wrote:
>> Like others have mentioned I took off the low pressure switch (F
>> 73) located in
> the right
>> plenum and planned on filling her up there however it seems like the 
>> threaded male connection with the schrader valve there is a metric 10

>> mm thread size which won't work with anything I can get at Autozone 
>> or Advance Auto parts. I am trying to avoid spending $100 bucks on 
>> the high end manifold gage set or paying a shop $120 to fix it for 
>> me.
>
> I'm almost in the same boat.  With 3 Audis with weak or no AC, I 
> thought I'd be better off investing in the equipment and doing it 
> myself. I bought the not-quite high-end manifold gage set ($60 at 
> Robbins, a supplier to mechanics in S. NH, not the $39 set at the 
> local national consumer chain.
> Plus another $30 in the R134a-specific hoses.). I bought the R134a 
> adapters.
> I haven't gotten around to actually doing the conversion(s) yet.   
> But my
> understanding so far is that the gage sets needs to tap into both the 
> high- and low-pressure sides of the system, so you still need to have 
> access to a low-pressure side valve.
>
> My am also under the impression is that the valve on the compressor is

> meant to drain the oil from the compressor, but as it is on the low- 
> pressure side,
> -- and here I'm not 100% sure/convinced -- it can be used to recharge 
> the system. I'll leave it to someone with more experience to confirm 
> or reject that idea.
>
> --
> Kent McLean
> '91 200 TQA #1, for sale
> '91 200 TQA #2, no name yet
> '94 100 S Avant, "Moody"
> '89 200 TQ, "Bad Puppy", up in smoke

_______________________________________________
S-CAR-List mailing list
S-CAR-List at audifans.com
http://www.audifans.com/mailman/listinfo/s-car-list