[s-cars] S6 pinging woes - the continuation
djdawson2 at aol.com
djdawson2 at aol.com
Fri Aug 14 11:52:49 PDT 2009
1) Your block should be fine. Spend some time getting the surface of the block cleaned up... emery cloth will do fine. You shouldn't find any actual metal damage on the surface of the block.
2) Clean your head up as well. However, there is a very good chance you will find metal damage on the head. If you can catch your fingernail in the burn mark, get it welded up and then resurfaced.
3) Your pistons look good. Based on the pic, it doesn't look like #5 got hurt at all. This is very good news. Forget about the piston/cylinder slop... unless you intend to consider rebuilding the bottom end. If the engine performed well prior to this failure, it will be fine after you repair it.
Why this happens? I couldn't state any facts, but would speculate that it is a combination of high boost along with the Audi I-5 engine's tendency to build more heat at the firewall (#5) end of the engine.
Good luck with the repairs. Oh... and consider using ARP studs on your head (this is a test to see if QSHIPQ is reading).
Dave
-----Original Message-----
From: Bares, Vittorio <Vittorio.Bares at nuance.com>
To: djdawson2 at aol.com; t44tqtro at gmail.com; s-car-list at audifans.com
Sent: Thu, Aug 13, 2009 8:31 pm
Subject: RE: [s-cars] S6 pinging woes - the continuation
U da man!!
Take a look here: http://picasaweb.google.com/BlissRally/95S6HeadGasket?authkey=Gv1sRgCLTZ_KHcwtL9bA#
Now – couple of questions:
the
block – you can see in the pic the burn mark – any reason to
believe this will create more issues with a new gasket?
the
head – not nearly as noticeable burn mark – I would think this
would be fine.
Pistons
have some slop, I understand I can check this with a feeler gauge? Anyone
know the spec on it?
And finally, what causes this?
Thanks,
Vittorio -
From:
djdawson2 at aol.com [mailto:djdawson2 at aol.com]
Sent: Sunday, August 02, 2009
12:36 AM
To: Bares, Vittorio; t44tqtro at gmail.com;
s-car-list at audifans.com
Subject: Re: [s-cars] S6 pinging
woes - the continuation
Who's your daddy? Who made the call?
Seriously, pull the head and take a good long look at the cylinder head
material between 4 and 5... make sure there isn't a groove burnt in it.
Also, take a very close look at the top of your #5 piston to make sure that
part of it isn't missing from the detonation.
If you're lucky, you will only find that the headgasket material is gone
between the cylinders.
BTW, you're not losing coolant, finding it in the oil, or blowing smoke because
your gasket is blown between cylinders, not between a cylinder and the water
jacket or oil passage.
Good luck.
Dave0A
-----Original
Message-----
From: Bares, Vittorio <Vittorio.Bares at nuance.com>
To: djdawson2 at aol.com; t44tqtro at gmail.com; s-car-list at audifans.com
Sent: Sat, Aug 1, 2009 8:42 pm
Subject: RE: [s-cars] S6 pinging woes - the continuation
Ok -
Compression Test (cold motor):
#1 155
#2 145
#3 125
#4 50
#5 60
Leakdown (warm motor)
#1 13%
#2 20%
#3 50%
#4 Near 100%
#5 Near 100%
When applying air pressure to #3, some air coming out of #4
When applying air pressure to #4, lots of air coming out of #5
When applying air pressure to #5, lots of air coming out of #4
So, head is going to need to come off - I'm just surprised I'm not:
a) eating *more* coolant than I am
b) have water in the oil, or oil in coolant
c) blowing billowing clouds of something from the tail pipe
Anyway, I'm hoping that I can just take the head off, replace the
headgasket (I have a metal one I can put on) and put it back on. Seems
to make sense to put some ARP studs in there - this is all best case
scenario - I guess I'll know more once the head comes off...
Comments?
Vittorio -
-----Original Message-----
From: s-car-list-bounces at audifans.com
[mailto:s-car-list-bounces at audifans.com] On Behalf Of djdawson2 at aol.com
Sent: Tuesday, July 28, 2009 1:00 PM
To: t44tqtro at gmail.com; s-car-list at audifans.com
Subject: Re: [s-cars] S6 pinging woes - the continuation
I believe that 30 minutes with a cheapo compression gauge is going to
give the answer... call it pre-ignition or detonation.
There are many documented cases of headgasket failure between 2 adjacent
cylinders.? The headgasket fails, then it burns a little groove in the
cylinder head between those 2 cylinders... allowing flame travel...
BTDT.
The one I experienced was between 4 and 5.? 5 was being pre-ignited.?
The result was an engine that sounded like it was "pinging" under any
and all conditions, even idle.
Letting this go for too long will result in total failure of a piston.
I would urge you to do a compression test before doing anything else.
Dave
-----Original Message-----
From: Taka Mizutani <t44tqtro at gmail.com>
To: s-car-list at audifans.com
Sent: Tue, Jul 28, 2009 10:50 am
Subject: Re: [s
-cars] S6 pinging woes - the continuation
You've just contradicted yourself, Brett- if the fuel/air charge ignites
prematurely, you get a large increase in cylinder pressure, which causes
all
sorts of bad things to happen to the engine.
You've stated this below as well as stating that it doesn't.
Anyway, the bottom line is that it's bad, the OP may have damaged
his/her
engine and it should be checked out. Having that happen with all of the
high
boost mods taken out is a bad sign.
I'd also check the fuel system to make sure that you're getting the
proper
amount of fuel actually delivered- if the pump or FPR or injectors are
not
doing their jobs, the computer might think it's sending enough fuel when
it's not.
Taka
On Tue, Jul 28, 2009 at 11:48 AM, Brett Dikeman
<brett.dikeman at gmail.com>wrote:
>
> Pre-ignition does not increase cylinder pressures and temperatures
> much beyond normal values (I think). Pre-ignition is bad because it
> puts more force on the engine internals, and in ways it wasn't
> designed...f
or example, if power is developed at exactly TDC, all the
> force goes against the rod, crank, bearings, and head gasket/bolts,
> instead of applying torque on the crank. Detonation does increase
> pressure and temperature, massively- it melts and bends things.
>
> Cody's recommendation to drain/filter the oil and check the engine oil
> filter are sound.
>
> Brett
>
_______________________________________________
S-CAR-List mailing list
http://audifans.com/mailman/listinfo/s-car-list
http://www.audifans.com/kb/List_information
_______________________________________________
S-CAR-List mailing list
http://audifans.com/mailman/listinfo/s-car-list
http://www.audifans.com/kb/List_information
More information about the S-CAR-List
mailing list