[urq] 3B on WR Block

Claus Vegener vegener at post7.tele.dk
Wed May 30 13:26:16 EDT 2007


Not to the 034EFI ECU but I have mounted a single knock-sensor (3B) and 
bought a knock-sensing device
yesterday from http://www.viatrack.ca  . Not arrieved yet. And ordered an 
Innovative WB lambda too.

Claus

----- Original Message ----- 
From: "Ingo Rautenberg" <ingo.rautenberg at gmail.com>
To: "Claus Vegener" <vegener at post7.tele.dk>
Cc: "Brandon Rogers" <brogers at terrix.com>; "'Alan Pemberton'" 
<alan_pemberton at telus.net>; "'Roman'" <klodzko at hotmail.com>; 
<urq at audifans.com>; "'leszekf'" <leszekf at sbcglobal.net>
Sent: Wednesday, May 30, 2007 7:13 PM
Subject: 3B on WR Block


> Is there any kind of knock-sensing in this setup?
>
> Ingo
>
> On May 30, 2007, at 1:06 PM, Claus Vegener wrote:
>
>> I am running 034EFI IIc
>> WR bored to 83 mm; stroker crank 92 mm = 2.5 litre
>> Eagle rods
>> AAN valvecover with coil-on-plugs
>> AAN flatbelt for generator and WR hydraulic pump
>> Garrett GT35R82 turbo. Custom EM and 3B IM cut before the bend for 
>> throttle so throttle is relocated.
>> IC just in front of new 034EFI radiator with new fans
>>
>> Problems with the trigger-wheel
>>
>> To-morrow ought to receive carbon sports hood from Roman (hi Roman)
>> Claus
>> ----- Original Message ----- From: "Ingo Rautenberg" 
>> <ingo.rautenberg at gmail.com>
>> To: "Claus Vegener" <vegener at post7.tele.dk>
>> Cc: "Brandon Rogers" <brogers at terrix.com>; "'Alan Pemberton'" 
>> <alan_pemberton at telus.net>; "'Roman'" <klodzko at hotmail.com>; 
>> <urq at audifans.com>; "'leszekf'" <leszekf at sbcglobal.net>
>> Sent: Wednesday, May 30, 2007 6:53 PM
>> Subject: Re: [urq] urq Digest, Vol 43, Issue 31 (MC Head on WX  engine 
>> question)
>>
>>
>>> 3B head on a WR or WX block?  This intrigues me, Claus.  Are you 
>>> running 3B ECU, then or???
>>>
>>> Ingo
>>>
>>> On May 30, 2007, at 11:55 AM, Claus Vegener wrote:
>>>
>>>> I have seen that picture but choose a bit more easy approch when  I 
>>>> placed a
>>>> 3B head on my ur-quattro WR block 1983.
>>>> Instead of welding  I molded with chemical metal from Lochtite,   which 
>>>> can
>>>> take 150 deg C, just a flat area on the side top of the block.
>>>> An inch deep too to support.
>>>> Did not made it oval because an inch deeper the canal is round -   and 
>>>> the
>>>> canal is only used when warming up.
>>>> I have not run much with that still but it seems to work. I have   used 
>>>> the
>>>> same metal to repair a hole from a bent rod at the side of  a 3B   and 
>>>> that is
>>>> 50.000 km ago.
>>>> The reason for not filling up the head with some aluminum was the 
>>>> problem
>>>> with the gasket where I use a S6 or new type 3B metal gasket.
>>>> The gasket have the oval hole too.
>>>> Claus
>
> 



More information about the urq mailing list