[urq] Clutch for Urq with 3b?

[Chris Miller]

OK, clutch kit spec is 200q20v, including the small pilot bearing in the
crankshaft.  Is the throwout bearing compatible with the stock urq locker
transmission, or do we need to order a different one than in the 200q20v
kit?

 

On the bellhousing, is it just drilling the appropriate hole larger to
handle both sensors?  Probably obvious and I'll look when it stops raining
here.

Thanks Chris

 

From: dgraber460 at aol.com [mailto:dgraber460 at aol.com] 
Sent: Thursday, October 27, 2011 9:00 PM
To: c1j1miller at aol.com; wnstedman at gmail.com; urq at audifans.com
Subject: Re: [urq] Clutch for Urq with 3b?

 


The flywheel and clutch from the WX will not work with the 3B.

Most of us have just used the 3B set up. You will need to modify the
bell-housing to accept the twin flywheel sensor set up used by the 3B. And
as mentioned you will need to replace the pilot bearing.

Dennis 

Denver

 

-----Original Message-----
From: Chris Miller <c1j1miller at aol.com>
To: 'W.Stedman' <wnstedman at gmail.com>; urq <urq at audifans.com>
Sent: Thu, Oct 27, 2011 6:46 pm
Subject: Re: [urq] Clutch for Urq with 3b?

I'm in the same boat; 85 urq getting a 3b from a 200q20v.  My initial
searching shows that the non-torsen 016 locker transmission has a different
transmission output spline size than the later torsen 016 like in the
200q20v.  So, can't use the same clutch disk.  I will confirm this when it
stops raining, as I have a disk off the 200q20v.  Also, I believe I read
that the throwout bearing is also different.
 
Looks like a standard setup for the urq or for an '86-88 5000 turbo is
correct, or performance versions of both.
Are you using the flywheel from the urq or from the 20vt?  I'm hoping to use
the 3b flywheel, and I'm not sure if that is the same as my urq engine is
long gone.
 
Any suggestions?   Sorry to jump on your thread; are you also using the
engine from a 200q20v, or off an S2?
 
Chris
 
 
 
-----Original Message-----
From: urq-bounces at audifans.com [mailto:urq-bounces at audifans.com
<mailto:urq-bounces at audifans.com?> ] On Behalf
Of W.Stedman
Sent: Thursday, October 27, 2011 8:33 PM
To: urq at audifans.com
Subject: [urq] Clutch for Urq with 3b?
 
I have a 1982 Urq and am planning on putting in a 3b 20vt motor and flywheel
in it. And is there a special clutch and pressure plate combo I need to use
with this? 
 
_______________________________________________
Audifans urq mailing list
Manage your list connection: http://www.audifans.com/mailman/listinfo/urq
http://www.audifans.com/kb/List_information
 
Pictures/Polls/Database at: http://autos.groups.yahoo.com/group/urquattro/
 
-----
No virus found in this message.
Checked by AVG - www.avg.com <http://www.avg.com/> 
Version: 2012.0.1834 / Virus Database: 2092/4578 - Release Date: 10/27/11
 
_______________________________________________
Audifans urq mailing list
Manage your list connection: http://www.audifans.com/mailman/listinfo/urq
http://www.audifans.com/kb/List_information
 
Pictures/Polls/Database at: http://autos.groups.yahoo.com/group/urquattro/
 
  _____  


No virus found in this message.
Checked by AVG - www.avg.com
Version: 2012.0.1834 / Virus Database: 2092/4578 - Release Date: 10/27/11