[V8] V8 not starting

[munir akhtar khan]

I removed TPS, ISV and checked G70 (airflow meter) and found all OK.After 92 the 
F60 and WoT are checked by a multimeter and confirming continuity 
(zero resistance) between point 4 & 6 at close but no continuity after slight 
open. ISV cleaned with WD40 and air pressure. both reinstalled.Now my focus has 
shifted to G28 (RPM sensor).  i want to check it without removing but could not 
find three pin connector. can someone guide me where is the connector and how to 
approach?BTW how to share pictures here coz i found a tool to remove and 
reinstall TPS easily (relatively) and i took picture of it which i want to 
share.Thanks



________________________________
From: George Tur <getur at optonline.net>
To: munir akhtar khan <munirbaluch at yahoo.com>
Sent: Tue, December 7, 2010 6:24:30 AM
Subject: Re: [V8] V8 not starting

Munir, the document is in pdf format and is 120 MB in size so I doubt if I could 
send it as an attachment to yahoo. I think they have a 2 or 3 MB limit on 
attachments. Is there an ftp server available that I could upload the pdf to?

Regards

George


On Dec 6, 2010, at 2:00 AM, munir akhtar khan wrote:

Thank you George,
>In which format do u have this manual. i have one for 3.6 and 4.2  in PDF but it 
>is in German language and i ve to translate it on Google translator when needed. 
>One of fellow Audi user sent me as attachment. if your manual can be sent as an 
>attachment i ll be highly obliged.
>Munir
>
>
________________________________
From: George Tur <getur at optonline.net>
>To: munir akhtar khan <munirbaluch at yahoo.com>
>Sent: Sat, December 4, 2010 8:02:49 PM
>Subject: Re: [V8] V8 not starting
>
>Munir, attached are some screens from the 3.6 V8 manual that show the position 
>and trouble shooting procedure for the throttle position switch. I believe it 
>should be the same for the 4.2 V8. I hope it helps. Good luck.
>
>Regards
>
>George
>
>On Dec 4, 2010, at 11:18 AM, munir akhtar khan wrote:
>
>> No it doesn't start even when it is cold and code for flywheel sensor is 
2111 
>> but i got 2121.Which is most likely related to TPS. How to check or replace 
>>the 
>> TPS?If links for a picture of these steps can be posted, it would be a great 
>> help.
>> Munir
>> 
>> 
>> 
>> 
>> ________________________________
>> From: "cobram at juno.com" <cobram at juno.com>
>> To: munirbaluch at yahoo.com
>> Cc: v8 at audifans.com
>> Sent: Sat, December 4, 2010 6:57:45 PM
>> Subject: Re: [V8] V8 not starting
>> 
>> If it restarts after things cool down you have a bad flywheel sender. 
>> Check the archives, there's plenty in there about it.
>> 
>> BCNU,
>> Don't ever take a fence down until you know the reason it was put up.
>> 
>> munir akhtar khan <munirbaluch at yahoo.com> writes:
>>> My V8 with ABH not starting after shut down while it was 
>>> idling.pulled code 
>>> 2121.how to proceed?  Munir
>> 
>> 
>> 
>> 
>> _______________________________________________
>> Audifans V8 mailing list
>> Send posts to: mailto:V8 at audifans.com
>> Manage your list connection: http://www.audifans.com/mailman/listinfo/v8
>> 
>> You can help keep the audifans site running by shopping 
>>at http://audifans.com/shop/
>> 
>
>
>