[Vwdiesel] ECO -- VW ----( Hagars ECO -- Bunny Bondo )
Val Christian
val at swamps.roc.ny.us
Thu Apr 14 12:58:58 EDT 2005
Rob,
I'll give short lip service to the topic. You'll need to tune so that you
can load the intake on once cyl when the other has a back wave from a
closing valve. You also want to look at the total system resonance to
reduce noise.
I can't cookbook it for you, because it's been a long time since I've done
this stuff. The reference text I would use is Acoustics, by Beraneck.
I'd probably get the rest of the system optimized first, and make the
inlet timing issues the final embelishment. I don't know exactly what
toolkits would be available right now. Years ago, NASTRAN facilitated
modeling. I'd probably look at the toolkits for MATLAB. Simulink
might be a help, but you're going to want to model pressure and flow,
through different speeds.
My acoustic life was horn design, and some acoustic modeling. This stuff
is a little different, but it's still just like designing a ducted port
type loudspeaker system.
If anyone uses a more current Acoustics text, I'd be interested. Beranek's
book is about 50 years old.
Val
>
> Bob,
>
> In my fixed speed 1800 RPM genset application with a NA 1980, 1.5 D, I am
> after absolute minimun fuel consumption possible. I thought of
> experimenting with tuned intake runners as you mention as a way of improving
> power and efficiency (lower fuel use). Any idea of the mathematical formula
> to calculate runner length? Is the wave propagation at the speed of sound.
> 1140 ft/sec and independent of flow velocity in the pipe?
>
> I am also interested in the potential benefit that advancing the camshaft
> may have on my application as well, although I recently read that a whole
> belt notch on the cam gear will cause valve piston collisions. Not much
> room upstairs in these high compression engines. I'm used to working on
> obsolete (by that I mean pretty much all of them now) gasoline engines with
> auditorium sized head volumes.
>
> Rob
>
> ----- Original Message -----
> From: <slatersfb at aol.com>
> To: <vwdiesel at vwfans.com>
> Sent: Thursday, April 14, 2005 10:38 AM
> Subject: [Vwdiesel] ECO -- VW ----( Hagars ECO -- Bunny Bondo )
>
>
> > Check out the long intake runners on N/A motor. These are a tuned length
> to create positive wave pressure at the time intake valve opens. Wave tuning
> actually stuffs incoming charge into cylinder, rather than relying on vacuum
> to suck it in.
> > Waves are created in runner when intake valve slams shut on incoming
> charge, and another when intake opens. These waves travel backwards, up
> through runner and are reflected back down from the open end. The length of
> runner determines the rpm at which the positive wave arrives at intake valve
> opening.
> > N/A two stroke motors barely run without wave tuning in the form of an
> expansion chamber.
> >
> > Bob
> >
> >
> > *********
> >
> > And opening that intake
> > valve at 5 psi overpressure is different --- than opening it at a slight
> > underpressure.
> > _______________________________________________
> > Vwdiesel mailing list
> > Vwdiesel at vwfans.com
> > http://www.audifans.com/mailman/listinfo/vwdiesel
> >
>
> _______________________________________________
> Vwdiesel mailing list
> Vwdiesel at vwfans.com
> http://www.audifans.com/mailman/listinfo/vwdiesel
>
More information about the Vwdiesel
mailing list