[Vwdiesel] Crank Yank Sprocket Tool at MetalNerd RE: Oil leak

[Rudy Petersen]

 That is a nice Tool and would be good if you did it every day but it's
overkill.  I made mine in an hour out of a piece of Flatbar that I paid
$2.00 for!

Rudy

-----Original Message-----
From: vwdiesel-bounces at vwfans.com [mailto:vwdiesel-bounces at vwfans.com] On
Behalf Of Will Taygan
Sent: Monday, December 28, 2009 1:08 PM
To: vwdiesel
Subject: [Vwdiesel] Crank Yank Sprocket Tool at MetalNerd RE: Oil leak

Looks like MetalNerd has mass-produced an attachment like Kurt and Rudy
recommend!  Not cheap, though:

http://www.metalnerd.com/images/products/cat05/mnyankp.jpg

http://www.metalnerd.com/cat05.htm

Now, can I justify buying another tool? ;)

(Struts just gave out on the ecodiesel (flat - not just bouncy)  so I might
need to fix that first.. haha..)

Will in Alaska.

On Sat, 2009-12-19 at 19:28 -0600, James Hansen wrote:
> I have used an inch air impact gun, step down to the socket with 
> adapters, flick the trigger and it's off before you can break 
> anything. I can jack up on the tranny side to get the belt side lower, 
> pointed down to make it easier to work.
> -james
> 
> > -----Original Message-----
> > From: vwdiesel-bounces at vwfans.com 
> > [mailto:vwdiesel-bounces at vwfans.com]
> > On Behalf Of Will Taygan
> > Sent: Saturday, December 19, 2009 12:02 PM
> > To: vwdiesel
> > Subject: Re: [Vwdiesel] Oil leak
> > 
> > Thanks Kurt, I like the tips.
> > 
> > I'm getting ready to replace all the seals on my freshly rebuilt 
> > 1.6NA in the '82 Westy.  Seems like the rebuild shop used "Top Line"
seals.
> > Not so good?  poorly installed?  overpressured crankcase?  dunno.
> > Putting in a Sabo OEM (Brazil) set $42 from AutohausAZ.
> > 
> > Question is, how do you like to lock the main crank to remove the bolt?
> > Last time I dropped the oil pan and stuck a piece of wood between 
> > the crank and block.  And my goodness, the oil pan is a tight fit at 
> > the tranny on the Vanagons.
> > 
> > Will in Alaska.
> > 
> > On Fri, 2009-12-18 at 12:52 -0500, Kurt Nolte wrote:
> > > Joe,
> > 
> > > If you can handle a timing belt, the front crank seal is just a 
> > > few short steps past that. You'll need to add a new seal, seal 
> > > carrier gasket, and a new crankshaft bolt to your list of parts 
> > > (should
> > probably
> > > replace the TB, if it's been oil-fouled). If you have access to a
> > vice
> > > then the job is /super easy/.
> > >
> > > Remove everything as though you were going to do a timing belt job.
> > > Remove the sprocket, discard stretch-bolt securing it.
> > > Remove the handful of small bolts holding the seal carrier to the 
> > > engine, and pull the seal carrier. Make sure all the gasketing is 
> > > cleaned away and you have bare block and bare carrier.
> > >
> > > To remove and install the seal from the carrier, I use a bench 
> > > vice
> > and
> > > two sockets. One is ~the same diameter as the seal, and the other 
> > > is
> > big
> > > enough for the seal to fit inside. I have big sockets laying 
> > > around,
> > but
> > > you could use a bit of pipe or something for either of these bits.
> > >
> > > Wrap or tape the edge of your bigger pipe, set it against the 
> > > sealing surface of the carrier, then fit your smaller socket on 
> > > the other
> > side
> > > to press against the seal. Slowly close the vice, out comes the seal.
> > >
> > > Wet the new seal with oil, get it settled against the carrier, and 
> > > gently push it in with the same method until it's well seated.
> > >
> > > New gasket, reinstall, new crank bolt, and finish your timing belt
> > job.
> > >
> > > Of course, you probably knew all of that, now that I spot your 
> > > "more than I'm willing to do" comment.
> > >
> > > -Kurt
> > >
> > > Joe wrote:
> > > > Actually, my oil leak appears to be on the "front" of the 
> > > > engine,
> > as it's
> > > > starting to throw oil off the timing belt.  (I run it coverless)
> > And the
> > > > drip marks on the driveway are primarily on that side.  I 
> > > > usually
> > have to
> > > > feed it a quart every 500 miles or so.  Haven't been able to 
> > > > locate
> > it
> > > > precisely yet.  I'm afraid it's the crankcase seal, which is 
> > > > more
> > than I can
> > > > do... Or rather, more than I am willing to do.
> > > >
> > > > Joe
> > -snip-
> > 
> > _______________________________________________
> > Vwdiesel mailing list
> > Vwdiesel at vwfans.com
> > http://www.audifans.com/mailman/listinfo/vwdiesel
> 
> 


_______________________________________________
Vwdiesel mailing list
Vwdiesel at vwfans.com
http://www.audifans.com/mailman/listinfo/vwdiesel