FW: Rear Child Seat Anchors, 1989-91 100/200,1990-91 V8,1988-91 80&90

["Dupree, Jim" <dupree@alldata.com>]

I'm sorry if this is going out twice to everyone but it never came back
to me and child safety is an important issue to me.

>----------
>From: 	Dupree, Jim
>Sent: 	Wednesday, October 08, 1997 3:43 PM
>To: 	C1J1Miller@aol.com; quattro@coimbra.ans.net; 'Scott M.'
>Subject: 	RE: Rear Child Seat Anchors, 1989-91 100/200,1990-91 V8,1988-91
>80&90
>
>These early TSB's on child seat restraints have been superseded by TSB Group
>69 # 97-01, dated July 17, 1997. This new TSB covers all vehicles from 1979.
>TSB's can be ordered from Dyment distribution at (800) 544-8021 or Fax (800)
>572-1438. I have no affiliation with Dyment but do find them to be a good
>source of information but not a cheap one. For $40 a year you can subscribe
>to the Audi TSB's and they send you the new one each month.
>Jim Dupree
>1984 4KQ
>1984 4K
>
>----------
>From: 	Scott M.[SMTP:scottmo@teleport.com]
>Sent: 	Wednesday, October 08, 1997 12:42 PM
>To: 	C1J1Miller@aol.com; quattro@coimbra.ans.net
>Subject: 	Rear Child Seat Anchors, 1989-91 100/200,1990-91 V8,1988-91 80&90
>
>Chris Miller's new arrival (Congrats Chris!) and his
>discussion on the rear child seat mounting reminded me of a
>technical bulletin that may be useful for those Q-listers
>with children. This bulletin (Group 68 # 91-06) mentions
>that three additional child seat anchors can be added to
>the rear parcel shelf on the 1989-'91 100/200's and on the
>90-91 Audi V8's. There is also a bulletin that covers the
>80 & 90 Models 1988-91 (Group 68 # 91-05). The latest
>Bentley Manual for the 1989-91 100/200 shows these anchors
>in group 68-40.
>
>On the 100/200/V8 If you look in the trunk area underneath
>the rear parcel shelf you should see three sets of mounting
>locations, one in the center and two on each side. These
>mounting locations have one large hole in the center and
>three smaller holes already punched in the sheetmetal.
>
>The top of the rear parcel shelf needs to be notched (cut)
>to allow the following parts to be installed. Basically the
>installation involves pop riveting a large support washer
>from the trunk side and then bolting a bracket from the top
>of the parcel shelf. There is a trim cap that covers this
>bracket.
>
>100/200 parts list:
>
>443 887 301B Cap
>N 010 240 22 Mounting Bolt
>443 887 269 Bracket
>N 904 375 01 Blind Rivet
>810 019 829 Spacer (for mounting bolt)
>443 887 077C Washer (main support washer)
>321 867 164 Plug ?
>443 887 301 Cover (can be installed when anchors are not in
>use)
>
>The 80&90 Models may use alternative parts.
>
>HTH
>Scott M.
>89 200TQ
>CHIP-DIPPEN-CHILD-SECURING-DUDE
>
>
>