[V8] Re: CV boot replacement: stripped inner cv joint bolts

[Paul Waterloo]

It's not too bad, I did the same thing with my A8 before I got the tool.
Just get one that goes on a socket, put it in place and drive it in with a
ball pen hammer. It should seat enough to get it loose.

Good luck.

Paul


----- Original Message -----
From: "Ed Kellock" <ekellock at juno.com>
To: <200q20v at audifans.com>; <v8 at audifans.com>; <quattro at audifans.com>
Sent: Sunday, October 27, 2002 11:32 PM
Subject: [V8] Re: CV boot replacement: stripped inner cv joint bolts


> Hi, my name is Ed and I'm a Monkey Lad.
>
> I was indeed using the wrong tool.  These bolts have 12 points not six
> which means they are not Torx bolts, but I was using Torx bits on them.
> I just didn't even look or notice.  Stupid, stupid.  I did get 3 of them
> loose.  But the other 3 are somewhat stripped.  My only hope now is that
> there will be enough left that the proper tool will still be able to
> work.
>
> Thanks to Mike and Gary Andersone for pointing this out to me.
>
> Triple square is it?  I'll be tool shopping tomorrow.
>
> Ed
>
> On Sun, 27 Oct 2002 23:26:04 -0500 "Michael Sylvester"
> <mike.sylvester at worldnet.att.net> writes:
> > Those are not torx bolts, they are what is called a triple square.
> > I assume that you are using the correct tool and are just confused
> > on the
> > name.
> > If you are actually using a torx, then that may be the problem.
> >
> > If it is truly stripped, then you'll need to be creative.
> > Find something that that is close to fitting into the hole and
> > hammer it in,
> > e.g. a large torx bit that is too big.
> >
> > Mike Sylvester
> >
> >
> >
> > ----- Original Message -----
> > From: "Ed Kellock" <ekellock at juno.com>
> > To: <quattro at audifans.com>; <v8 at audifans.com>;
> > <200q20v at audifans.com>
> > Sent: Sunday, October 27, 2002 10:16 PM
> > Subject: CV boot replacement: stripped inner cv joint bolts
> >
> >
> > > Set out to replace the driver's side outer CV boot on my 89 200q
> > today...
> > >
> > > Three of the six Torx head bolts that attach the inner CV joint to
> > the
> > > transimission are stripped.  The Torx heads are stripped.  Seems
> > the axle
> > > has been removed in the past and new bolts were not used and the
> > Torx was
> > > already compromised.  Joy.
> > >
> > > Aside from any ugly approach like saws, drills, or vise grips,
> > does
> > > anyone have any clever ideas?
> > >
> > > Ed
> > > Colorado Springs
> > >
> > > ________________________________________________________________
> > > Sign Up for Juno Platinum Internet Access Today
> > > Only $9.95 per month!
> > > Visit www.juno.com
> > > _______________________________________________
> > > 200q20v mailing list
> > > 200q20v at audifans.com
> > > http://www.audifans.com/mailman/listinfo/200q20v
> > >
> >
> >
> >
> >
>
> ________________________________________________________________
> Sign Up for Juno Platinum Internet Access Today
> Only $9.95 per month!
> Visit www.juno.com
> _______________________________________________
> Audifans v8 mailing list
> Send posts to: mailto:v8 at audifans.com
> Unsubscribe or Manage your list options at
http://www.audifans.com/mailman/listinfo/v8