[Es2] intercooler and oil cooler installed

[c1j1miller at aol.com]

I've found some 18x1.5 to AN adaptors; they're over $10 each, and I 
might need a second adaptor to get the right AN size.  I'd like to 
reuse the existing lines since they're in good shape.  I may wait until 
the motor is in the chassis to figure out the solution.  I can always 
cut off the fitting at the cooler end of the line and do what you did 
with a short piece of line.

Thanks, Chris

---
Chris Miller, Bolton, MA  c1j1miller at aol.com
'91 Audi coupe q, '85 Audi 4ksq, '81 VW Scirocco
'91 200q20v site ==> http://members.aol.com/c1j1miller/welcome.html

-----Original Message-----
From: Elijahallen92 at aol.com
To: C1J1Miller at aol.com; es2 at audifans.com
Sent: Tue, 19 Apr 2005 08:31:25 EDT
Subject: Re: [Es2] intercooler and oil cooler installed


Chris,
  I haven't checked my mail in a couple days so you may already have  
this
figured out but what I ended up doing is cutting the stock oil line at 
the  hard

tube and welding a bead on it and just using double hose clamps to hold 
the
-10 line from summit racing on. On the oil cooler side I just used the 
swivel
type -10 easy connect hose fitting. I can send pictures if you need 
them. If
you  don't want to use hose clamps Earl's make a weld on bung that you 
can weld
on to  the hard line and then use an AN fitting there as well. I was 
going to
do this  but ordered the wrong part so I just took the easy route.

Elijah

In a message dated 4/18/2005 9:37:34 AM Eastern Standard Time,
c1j1miller at aol.com writes:

OK,  posted too soon.  Checking my archives (which are way too big) I
see:  The Audi oil filter boss where the cooler lines attach are  
metric.
18x1.5
So I assume the other side is the same, where it attaches  to the stock
Audi oil cooler.  True/false?
Next to figure out the  fitting size on the new oil cooler.

---
Chris Miller, Bolton,  MA  c1j1miller at aol.com
'91 Audi coupe q, '85 Audi 4ksq, '81 VW  Scirocco
'91 200q20v site ==>  http://members.aol.com/c1j1miller/welcome.html

-----Original  Message-----
From: Miller, Chris  <chris.miller at infofoundry.com>
To: Elijahallen92 at aol.com;  es2 at audifans.com
Sent: Mon, 18 Apr 2005 09:31:39 -0400
Subject: RE:  [Es2] intercooler and oil cooler installed

I'm installing a similar  Mocal oil cooler to Elijah's, using the stock
oil cooler lines from the 3B.  Do you know offhand what adaptor is 
needed
to go from Audi lines to the  Mocal?
Chris

-----Original Message-----
From:  es2-bounces at audifans.com [mailto:es2-bounces at audifans.com] On
Behalf Of  Elijahallen92 at aol.com
Sent: Sunday, March 06, 2005 7:38 AM
To:  es2 at audifans.com
Subject: [Es2] intercooler and oil cooler  installed

Hey guys, I spent the day Saturday at a friends shop working  on the
coupe.
We fit a 24x12x3 FMIC and my 19 row mocal oil cooler. It  was a tight 
fit
but it  just made it. Here is a link to audiworld.  There is a picture
with the bumber  off and another with the bumber on  farther down in the
thread. I only had one  bolt in each side hand  tight on the bumber so 
it
sags a little but it it does   fit!!
_http://forums.audiworld.com/s4s6/msgs/54669.phtml_
(http://forums.audiworld.com/s4s6/msgs/54669.phtml)
Elijah
_______________________________________________
Es2  mailing  list
Es2 at audifans.com
http://www.audifans.com/mailman/listinfo/es2
_______________________________________________
Es2  mailing  list
Es2 at audifans.com
http://www.audifans.com/mailman/listinfo/es2

_______________________________________________
Es2  mailing  list
Es2 at audifans.com
http://www.audifans.com/mailman/listinfo/es2



_______________________________________________
Es2 mailing list
Es2 at audifans.com
http://www.audifans.com/mailman/listinfo/es2