re. 100Q finally started:bad distributor plate.

[Denis]

Hi, Ben,,,, yesterday evening i unscrewed almost all bolt .... 5 left. tranny almost ready to remove. By the way i WILL reface the flywheel and the pressure plate. My friend at Germaan garage told dont face them ...... for me, if it s faced then the clutch ll have to used until it took the old clutch paturn, understand ?, until then i cant get the clutch go one or take a grip . and the car cant move even in 1,2,3,4 or 5. 
By the way i ll replace the lock rode with a SS one.

Denis

I verified the ilnkage everything seems fine.

  ----- Original Message -----
  From: Ben Swann 
  To: Denis Julien 
  Sent: Tuesday, February 03, 2004 2:29 AM
  Subject: Re: re. 100Q finally started:bad distributor plate.


  Denis,
   
  Con't panic just yet - it could be something with your linkage.   Get up under there with a good light and mirror, and see if one or the ball and socket ends cam loose from the transmission.
   
  Hope that is it and you don't have to pull the tranny.
   
  Ben
    ----- Original Message ----- 
    From: Denis Julien 
    To: Ben Swann 
    Sent: Monday, February 02, 2004 1:37 PM
    Subject: Re: re. 100Q finally started:bad distributor plate.


    Ouch yessssssss.
    I ll reface the flywheel and the pressure plate ;-(
     
    For the reverse speed i dont know what is that. Worked fine before swap.
    Denis
     
     
      ----- Original Message ----- 
      From: Ben Swann 
      To: Denis Julien 
      Sent: Monday, February 02, 2004 12:14 PM
      Subject: Re: re. 100Q finally started:bad distributor plate.


      Denis,
       
      Sounds like a problem with the clutch not engaging - you may need to take trans again.  Ouch!
       
      I think you have a problem with vaccuem leak and idle control.  Although it could be several things, you may want to check the idle screw O-ring.
       
      Ben
        ----- Original Message ----- 
        From: Denis Julien 
        To: Ben Swann 
        Sent: Monday, February 02, 2004 11:10 AM
        Subject: Re: re. 100Q finally started:bad distributor plate.


        Ok Ben... good to me... after some starts and stop and minute running everything get normal,,, almost. The engine oscilated from 900 to 1500 RPM. Hard to start  too.
         
        thanks Ben
         
        Denis
         
        I still have problem to change oil seals CV flange , on the 90 FWD tranny.
         
         
        Oh,,, the 016 does not works.... the clutch slip and the car move just a little.
         And it doean not got to reverse !!! shit... i have to take off every thing i did.....
         

         
          ----- Original Message ----- 
          From: Ben Swann 
          To: Denis 
          Cc: quattro at audifans.com 
          Sent: Monday, February 02, 2004 9:58 AM
          Subject: re. 100Q finally started:bad distributor plate.


          Denis,
           
          There is no proper way to retrofit the distributor for 5000T/TQ as these are CIS and the one you have is CIS-E.  It could perhaps be done, but your best bet is to find a good CIS-E3 distributor, and save yourself the pain and agony of a retrofit.
           
          You may be able to pull the metering head off and clean things up - do with great cat and don't drop the plunger!
           
          Ben

          [It seems the distributor plate is not working well, it jamme at different level, that cause not meatering the fuel so no fuel go to injectors.

          After it run more than 10 sec, the time i got off the car, and play with the plate trought the air filter it ran ok.

          If i touch the accelerator pedal  the engine dont go back to idle seed, and speed to fast until i play again with the distr plate.

          Denis

          I m looking at my older distr from 5000T and 5000TQ unit if any way to fit it.

          Any advices ?]