oups mistake Re: re. 100Q finally started:bad distributor plate.
Denis
sparkplugvw at hotmail.com
Tue Feb 3 08:04:08 EST 2004
----- Original Message -----
From: Denis <sparkplugvw at hotmail.com>
To: quattro list <quattro at audifans.com>; Ben Swann <benswann at comcast.net>
Sent: Tuesday, February 03, 2004 8:00 AM
Subject: Re: re. 100Q finally started:bad distributor plate.
Hi, Ben,,,, yesterday evening i unscrewed almost all bolt .... 5 left.
tranny almost ready to remove. By the way i WILL reface the flywheel and the
pressure plate. My friend at Germaan garage told dont face them ...... for
me, if it s NOT faced then the clutch ll have to used until it took the old
clutch paturn, understand ?, until then i cant get the clutch go one or take
a grip . and the car cant move even in 1,2,3,4 or 5.
By the way i ll replace the lock rode with a SS one.
Denis
I verified the ilnkage everything seems fine.
----- Original Message -----
From: Ben Swann
To: Denis Julien
Sent: Tuesday, February 03, 2004 2:29 AM
Subject: Re: re. 100Q finally started:bad distributor plate.
Denis,
Con't panic just yet - it could be something with your linkage. Get up
under there with a good light and mirror, and see if one or the ball and
socket ends cam loose from the transmission.
Hope that is it and you don't have to pull the tranny.
Ben
----- Original Message -----
From: Denis Julien
To: Ben Swann
Sent: Monday, February 02, 2004 1:37 PM
Subject: Re: re. 100Q finally started:bad distributor plate.
Ouch yessssssss.
I ll reface the flywheel and the pressure plate ;-(
For the reverse speed i dont know what is that. Worked fine before swap.
Denis
----- Original Message -----
From: Ben Swann
To: Denis Julien
Sent: Monday, February 02, 2004 12:14 PM
Subject: Re: re. 100Q finally started:bad distributor plate.
Denis,
Sounds like a problem with the clutch not engaging - you may need to
take trans again. Ouch!
I think you have a problem with vaccuem leak and idle control.
Although it could be several things, you may want to check the idle screw
O-ring.
Ben
----- Original Message -----
From: Denis Julien
To: Ben Swann
Sent: Monday, February 02, 2004 11:10 AM
Subject: Re: re. 100Q finally started:bad distributor plate.
Ok Ben... good to me... after some starts and stop and minute
running everything get normal,,, almost. The engine oscilated from 900 to
1500 RPM. Hard to start too.
thanks Ben
Denis
I still have problem to change oil seals CV flange , on the 90 FWD
tranny.
Oh,,, the 016 does not works.... the clutch slip and the car move
just a little.
And it doean not got to reverse !!! shit... i have to take off
every thing i did.....
----- Original Message -----
From: Ben Swann
To: Denis
Cc: quattro at audifans.com
Sent: Monday, February 02, 2004 9:58 AM
Subject: re. 100Q finally started:bad distributor plate.
Denis,
There is no proper way to retrofit the distributor for 5000T/TQ as
these are CIS and the one you have is CIS-E. It could perhaps be done, but
your best bet is to find a good CIS-E3 distributor, and save yourself the
pain and agony of a retrofit.
You may be able to pull the metering head off and clean things
up - do with great cat and don't drop the plunger!
Ben
[It seems the distributor plate is not working well, it jamme at
different level, that cause not meatering the fuel so no fuel go to
injectors.
After it run more than 10 sec, the time i got off the car, and
play with the plate trought the air filter it ran ok.
If i touch the accelerator pedal the engine dont go back to idle
seed, and speed to fast until i play again with the distr plate.
Denis
I m looking at my older distr from 5000T and 5000TQ unit if any
way to fit it.
Any advices ?]
_______________________________________________
quattro mailing list
quattro at audifans.com
http://www.audifans.com/mailman/listinfo/quattro
More information about the quattro
mailing list