[s-cars] Ball bearing turbo

[Mark Strangways]

The 3071 is just the compressor cover right ?
Or is it the wheel as well.

I have the understanding that it is just the cover, but I did want to try 
the Garrett turbine housing.

Let me know what U think ?

Mark
----- Original Message ----- 
From: <djdawson2 at aol.com>
To: <Strangconst at rogers.com>; <james.murray at ericsson.com>; 
<HAHNMGH at peoplepc.com>; <s-car-list at audifans.com>
Sent: Tuesday, October 18, 2005 6:38 PM
Subject: Re: [s-cars] Ball bearing turbo


> Having pulled a GT30R off of my car, and installed a 3071 immediately 
> afterwards, I can tell you that the 3071 hits way faster than the regular 
> 30... making full boost before 3k rpm at higher altitudes.  I was using a 
> .63 turbine on both.  If there's any interest, I have a GT3071R that I 
> will not be using, as I removed it after 2000 miles to reinstall the 
> GT30R.  It is full Garrett, however, and does not have a KKK turbine 
> section.
>
> Dave
>
> -----Original Message-----
> From: Mark Strangways <Strangconst at rogers.com>
> To: djdawson2 at aol.com; james.murray at ericsson.com; HAHNMGH at peoplepc.com; 
> s-car-list at audifans.com
> Sent: Tue, 18 Oct 2005 18:29:53 -0400
> Subject: Re: [s-cars] Ball bearing turbo
>
>
> Yeah, the GT3071R would have been my choice had it been around when I did 
> my hybrid. The curves look very nice, and I would suspect it would pick up 
> faster than the GT30R that I have now.
>
> The upside with the GT30R is an unlimited amount of boost to redline.
>
> I may try to part with my hybrid to explore the 3071.
>
> Mark
> ----- Original Message ----- From: <djdawson2 at aol.com>
> To: <james.murray at ericsson.com>; <HAHNMGH at peoplepc.com>; 
> <s-car-list at audifans.com>
> Sent: Tuesday, October 18, 2005 11:47 AM
> Subject: Re: [s-cars] Ball bearing turbo
>
>> I would suggest the 3071. Javad has it with the KKK hot side. I ran it > 
>> on my car for awhile using the .63 A/R turbine, and it hits as early as 
>> an > RS2. It has the benefit of being able to move about 44lbs/min > 
>> efficiently, as opposed to only about 34lbs/min for the RS2.
>> Dave
>>
>> -----Original Message----- 
>> From: James Murray (QA/EMC) <james.murray at ericsson.com>
>> To: 'HAHNMGH at peoplepc.com' <HAHNMGH at peoplepc.com>; Audifans Audifans > 
>> <s-car-list at audifans.com>
>> Sent: Tue, 18 Oct 2005 08:29:20 -0500
>> Subject: Re: [s-cars] Ball bearing turbo
>>
>>
>> Mark, take a look at the turbo's offered by > 
>> http://www.034efi.com/index.php?cPath=21
>> The GT28RS sounds like what you are looking for...comparable to RS2, > 
>> however you
>> might want to consider the GT2871RS too.
>>
>> I have not tried any of these myself, however if you are looking for ball
>> bearing turbo's 034efi has a full line up for the I5 20V.
>>
>> /Jamu.
>> _______________________________________________
>> S-CAR-List mailing list
>> S-CAR-List at audifans.com
>> http://www.audifans.com/mailman/listinfo/s-car-list
>>
> _______________________________________________
> S-CAR-List mailing list
> S-CAR-List at audifans.com
> http://www.audifans.com/mailman/listinfo/s-car-list
>