[s-cars] 2B Camber Plate Group Buy - Initial Interest Poll

[Serge Filanovsky]

Whooooa, something is seriously off here, because I totally agree with
Pizzo, on this one.

But hey, Clancy, I'll take two sets of those plates since you're offering
them up for free. Or were you just running your mouth, with nothing to back
it up, ummm, again?

Serge


> Far from it.
> 
> 2Bennett actually has a business to run, imagine that! Employees and
> suppliers to pay, not to mention R&D cost to get something that fits nicely,
> bolts right in and gets you the adjustment you need to not chew up tires. I
> will gladly pay for someone to go through the R&D so that I don't have to
> cut and re-cut and try all over again just to get something that's hacked in
> the corner of my garage rather than a nice billet piece that was CNC'd.
> 
> If you can make it on your own, fine. Do it. Up to this moment, no one has
> come up with a better alignment solution than the 2B boys and I don't think
> you can do better than what they have by making something in your garage.
> 
> Let that be your motivation to prove me wrong, but I wouldn't risk my ass on
> the road at 100+mph with something I hacked together in my garage versus
> someone's $600 engineered solution.
> 
> Joe
> 
> On 9/24/05, Bill Clancy <clancybill at yahoo.com> wrote:
>> 
>> But they are toooo expensive. don't you think? They are metal plates
>> with holes drilled in them for 400+.
>> 
>> I can make those in my garage ( in probably will) for free).
>> 
>> Am I way off here?
>> 
>> Maybe the group price brings it down but I think Mr. 2-Bennet is ripping
>> us
>> off -- and doing a good job of it.
>> 
>> 
>> ----- Original Message -----
>> From: "Fred Munro" <munrof at sympatico.ca>
>> To: "Bill Clancy" <clancybill at yahoo.com>; "Mark Pollan"
>> <mark.pollan at mci.com>; <s-car-list at audifans.com>
>> Sent: Saturday, September 24, 2005 10:10 AM
>> Subject: RE: [s-cars] 2B Camber Plate Group Buy - Initial Interest Poll
>> 
>> 
>>> Actually, Bill, slotting the original plates only gives a limited amount
>>> of
>>> movement. The OD of the bottom barrel of the top mount contacts the ID
>> of
>>> the hole in the strut tower and at that point further slotting gets you
>>> nowhere (BTDT).
>>> 
>>> 2B has designed out this interference and their plates give a much
>> greater
>>> range of adjustment (ECS is similar I'm sure). The advantage of the 2B
>>> plate
>>> over ECS is that it also gives caster adjustment - that's why I chose
>>> them;
>>> I had a caster issue on the right side.
>>> 
>>> Fred Munro
>>> '94 S4
>>> 
>>> 
>>> -----Original Message-----
>>> From: s-car-list-bounces at audifans.com
>>> [mailto:s-car-list-bounces at audifans.com]On Behalf Of Bill Clancy
>>> Sent: September 24, 2005 11:16 AM
>>> To: Mark Pollan; s-car-list at audifans.com
>>> Subject: Re: [s-cars] 2B Camber Plate Group Buy - Initial Interest Poll
>>> 
>>> 
>>> I am not sure I see the value in these 2B plates. They are too
>>> expensive.
>>> I mean...I they're nice to have...but aren't they a bit pricey?
>>> You could get the same result by taking your original ones, slotting
>> them
>>> for the caster adjustment and moving the mounting holes to give the
>> proper
>>> camber. It would take about an hour to do this.
>>> 
>>> A while ago...someone sent a write up with a nice diagram on how to make
>>> the
>>> camber change. I apologize... I forget who it was.
>>> 
>>> 
>>> 
>>> ----- Original Message -----
>>> From: "Mark Pollan" <mark.pollan at mci.com>
>>> To: <s-car-list at audifans.com>
>>> Sent: Saturday, September 24, 2005 6:11 AM
>>> Subject: [s-cars] 2B Camber Plate Group Buy - Initial Interest Poll
>>> 
>>> 
>>>> OK well, I for one plan on keeping my car for a looooong time. So
>>>> capitalizing the cost of 2B even at a non-GB price, that's the one that
>>>> makes sense to me. I just cannot get myself the psychological block of
>>>> even
>>>> bending the fender lip for the ECS plate.
>>>> 
>>>> 
>>>> 
>>>> That said, who of you out there is a maybe and who is a for sure with
>> 2B?
>>>> Reply to me directly and at the end of next week I'll contact 2B. I
>> have
>>>> never dealt with them so if somebody could either pave the road or
>>>> provide
>>>> the appropriate point of contact that would be great.
>>>> 
>>>> 
>>>> 
>>>> Best regards,
>>>> 
>>>> 
>>>> 
>>>> Mark
>>>> 
>>>> _______________________________________________
>>>> S-CAR-List mailing list
>>>> S-CAR-List at audifans.com
>>>> http://www.audifans.com/mailman/listinfo/s-car-list
>>>> 
>>> 
>>> 
>>> _______________________________________________
>>> S-CAR-List mailing list
>>> S-CAR-List at audifans.com
>>> http://www.audifans.com/mailman/listinfo/s-car-list
>>> 
>>> 
>> 
>> 
>> _______________________________________________
>> S-CAR-List mailing list
>> S-CAR-List at audifans.com
>> http://www.audifans.com/mailman/listinfo/s-car-list
>> 
> _______________________________________________
> S-CAR-List mailing list
> S-CAR-List at audifans.com
> http://www.audifans.com/mailman/listinfo/s-car-list