[s-cars] 1995.5 UrS6 Remote Key Problems

[Jerry Scott]

Jay

Here's my file that might help with your problem.

Jerry

To reprogram your remote, use one key to turn the car on, get out and lock
the door using the other key (in the door), then press your remote buttons
(up to four times, for four different keys, 5 sec apart for each "pulse"),
then wait a minute or so, use the remote on the exterior key, and it should
be programmed and work correctly.
You need to press both the LOCK and UNLOCK buttons simultaneously to program
the remotes.

Also, according to the owner's manual, if you leave your car unused for 7
days or so, the remote will shut off to conserve battery power. Simply
unlock the car with the key in the door, and use the vehicle, the remote
should re-set.

Good luck,

Tom Winter
'95 S6 Avant

Here's how to get all the remotes to lock and unlock the doors. Which key
goes where does not matter, since we're reprogramming the remotes, not the
keys (keys are not programmable, anyway). There is no correlation between
key and remote, except for the prestige <g> of having the lighted key.


You will need:

1. All radio frequency remotes, with good batteries. Simplest is to replace
the batteries with new ones. I used Duracell DL2032.
2. Two keys. Coincidentally, the lighted key uses o-ne 625 watch/camera
battery, and bulb p/n N 902 625 01.

----------------------------------------------------------------------------
-----------------

1. Put one key in the ignition, and turn to "On", dash lights lit, but car
not running. Get out and close the driver's door. Might not be a bad idea to
roll down the driver's window, to ensure you don't lock yourself out (you
can't really, but it does give some peace of mind)
2. Put the other key in the driver's door lock.
3. Lock the car with the key in the driver's door.
4. Press both buttons on the first remote until car unlocks. This should
take about 5 seconds.
5. Set the remote aside, and select the next remote. Note: Do NOT turn the
ignition off between remotes.
6. Lock the car again with the key in the driver's door.
7. Press both buttons on the next remote until car unlocks.
8. If you have more than two remotes, repeat 6) and 7) with each succeeding
remote until done.
9. Turn the ignition off and remove the key.
10. The remotes should now all work. They should each lock and unlock the
car.

==============================================

Here's how to get the remotes to invoke the appropriate stored seat memory
position.

You will need:

1. All radio frequency remotes, as above.
2. Seat memory buttons programmed to desired settings.
----------------------------------------------------------------------------
------------------

1. Select the remote you want to invoke seat memory position one.
2. With the ignition off, open the driver's door, and leave it open.
3. Press seat memory button one, and wait for the seat and mirror to move to
the stored position.
4. With the driver's door still open, lock the car by pressing the lock
button on the remote. The car will lock, except for the driver's door.
5. Press and hold the seat memory button one.
6. Press and release the unlock button o-n the remote.
7. When the car unlocks, release seat memory button one. The first remote is
now programmed to both lock and unlock, and to invoke seat memory position
one. Set it aside as completed.
8. Repeat 12) through 16), using the appropriate seat memory button, until
you've programmed each of your remotes.

You have completed programming all your radio frequency remotes to invoke
the appropriate seat memory position.

===============================================

You can test success as follows:

1. Close the driver's door. Lock the car using remote one. The car should
lock.
2. Unlock car using remote one. The car should unlock.
3. Open the door. The seat and driver's door rearview should move to memory
position one.
4. Repeat 18), 19) and 20) with each succeeding remote.

Ta da! You should be in business!

-----Original Message-----
From: s-car-list-bounces at audifans.com
[mailto:s-car-list-bounces at audifans.com] On Behalf Of Jay M
Sent: Sunday, July 14, 2013 11:45 AM
To: AudiFans
Subject: [s-cars] 1995.5 UrS6 Remote Key Problems

My 1995.5 UrS6 Avant remote key lock/unlock has stopped working. I am now
inserting the key in the door lock to manually lock and unlock the doors.
When the remote was rendered useless in years past a simple replacement of
the single CR2032 battery in remote key  unit and all was good. However,
this time a new battery and the lock/unlock buttons on remote unit does
nothing. I have checked the respective fuse under the black cover near
driver side cowl in engine compartment and checked every fuse in fuse panel
on driver side of dash. All fuses appear to be good. I also tried to
reprogram unit as per directions in owner's manual but to no avail. The
owner's manual instructions appear to pertain to reprogramming the Infrared
Key Fob. Mine is not an infrared key fob as per the 1995 UrS6 cars. The
remote unit has a "LOCK" and "UNLOCK" button. Anybody know if there is a
better way to reprogram remote? Or, is there a way to isolate the problem
i.e. test the remote fob/transmitter or
  the receiving mechanism in the car to begin troubleshooting? Thanks.
 		 	   		  
_______________________________________________
S-CAR-List mailing list
http://audifans.com/mailman/listinfo/s-car-list
http://www.audifans.com/kb/List_information