[urq] 3" exhaust

[Martin Pajak]

David,

I want somethign that will not "restrict me" in case I do want to go RS2 in the future... 

It can't hurt, right?

Cheers
Martin Pajak

http://www.quattro.ca


---------- Original Message ----------------------------------
From: "Schaible, David" <David.Schaible at jrspharma.com>
Date:  Tue, 9 Aug 2005 12:37:35 -0400

>I'm skeptical as to the value of this, has someone validated that the
>exhaust is the flow restriction with a 3b running a k24 @ 2.5 bar ?
>
>I have had my 3b 200 avant setup like this for many years with the dual
>exhaust, and my friend a trusted tuner also believes it is not a
>restriction. 
>
>Maybe full on rs2 setup might require this...... but yeah I
>know.....it's certainly not going to hinder performance
>
>
>
>
>David Schaible
> 
>
> 
> 
>JRS Pharma LP
>2981 Rte 22
>Patterson, NY 12563
>845.878.3414
> 
>ALL STATEMENTS IN THIS CORRESPONDENCE ARE CONFIDENTIAL UNLESS OTHERWISE
>NOTED
> 
>
>-----Original Message-----
>From: Rich Letsinger [mailto:rletsinger at gmail.com] 
>Sent: Tuesday, August 09, 2005 12:24 PM
>To: urq at audifans.com
>Subject: Re: [urq] 3" exhaust
>
>Guys,
>
>I know you all like bolt-on upgrades and pride yourselves on DIY
>installation.  But I'd suggest you all look into good exhaust shops in
>your area to have a 3" system custom made on your car.  This is what I
>did and I'm very happy with it.
>
>Mine uses the factory 3B downpipe, cut off at the point where it
>splits in 2.  Right there if flares out to 3", bends under the car to
>a removable cat which I can replace with a test-pipe with the same
>connectors.  The exhaust goes up and over the driveshaft, which was
>difficult to do in 3", and then has a free flow muffler in the stock
>location, bends and comes right out the back.  Putting nice dual tips
>on it would've been easy for them, but I didn't care.
>
>It was done exactly as I specified and fits perfectly.  You could use
>any muffler to get the right tone, mine's a flowmaster and is quite
>loud and gruff sounding.  I chose alluminized steel because it's
>cheaper and easier to work with, but they'd have done stainless if I
>wanted.  I paid about $750 for this, took them half a day and it was
>right the first time.
>
>Consider it.
>
>Cheers,
>Rich
>_______________________________________________
>Audifans urq mailing list
>Send posts to: mailto:urq at audifans.com
>Manage your list connection:
>http://www.audifans.com/mailman/listinfo/urq
>Have an urq question?  Check the Audifans Knowledgebase!
>http://www.audi-quattro.org/cgi-bin/twiki/view/Audi/UrQuattro
>Have an urq answer? ... Please help others by adding to the KB ... all
>contributions welcome!
>
>______________________________________________________________________
>This e-mail has been scanned by MCI Message Labs Anti-Spam and
>Anti-Virus Managed Email Content Service.
>
>
>
>
>____________________________________________________________________
>
>This e-mail has been scanned for viruses by a Managed Email Content Service.
>_______________________________________________
>Audifans urq mailing list
>Send posts to: mailto:urq at audifans.com
>Manage your list connection: http://www.audifans.com/mailman/listinfo/urq
>Have an urq question?  Check the Audifans Knowledgebase!
>http://www.audi-quattro.org/cgi-bin/twiki/view/Audi/UrQuattro
>Have an urq answer? ... Please help others by adding to the KB ... all contributions welcome!
>