[V6-12v] Re: CV joint stuff

[Clive Young]

Guys

Oh no guess what . I noticed the "cage" area that holds the balls can go in
either way also . Ther is a fat edge and a more tapered edge. Now I am
really screwed. Anybody got a bently that shows pics of the CV joint being
assembled?. I have great ones on the 5000, but it is a different CV type
joint.


----- Original Message ----- 
From: "clive young" <cyoung1661 at rogers.com>
To: "Tom Christiansen" <tomchr at ee.washington.edu>
Cc: "Audi list" <v6-12v at audifans.com>
Sent: Friday, June 25, 2004 10:12 PM
Subject: [V6-12v] Re: CV joint stuff


> Tom
>
> The CV joint itself is made up of three main components.
>
> The outer housing , The "cage" and the inner housing for lack of  abtter
> term . The inner housing (after I got it out and cleaned up) I noticed
could
> go in two ways. The cage doesn't matter. The inner housing on one side has
a
> recessed ridge all the way around the outer edge I just don't know if it
> faces towards the car or wheel. If your CV joint came prepacked you may
not
> have seen this  I was just wondering if you noticed. I can send a digi pic
> if you think it would help
>
> Clive
>  ----- Original Message ----- 
> From: "Tom Christiansen" <tomchr at ee.washington.edu>
> To: "clive young" <cyoung1661 at rogers.com>; "Audi Mailing List"
> <v6-12v at audifans.com>
> Sent: Friday, June 25, 2004 10:03 PM
> Subject: CV joint stuff
>
>
> > Clive,
> >
> > I'm not sure which recessed part you are talking about. The inner joint
is
> > one unit and can only be mounted on the transmission the right way. To
get
> > the outer joint on correctly, the three little pieces need to be
installed
> > correctly.
> >
> > With the inner boot on and fastened and with the outer joint off,
install
> > the parts in the following order:
> >
> > 1) Outer boot.
> >
> > 2) Spring washer (notice that it curves slightly. If you hold the axle
> with
> > the open (outer) end facing up, the spring washer goes on curving up
like
> a
> > very shallow bowl. It pushes the spacer out that way.)
> >
> > 3) After the spring washer comes the spacer. The tapered end on the
spacer
> > faces the outer end of the axle.
> >
> > 4) Then install the circlip in the grove at the end of the axle.
> >
> > 5) Install CV joint (tap with plastic hammer until circlip engages).
> >
> > 6) Complete installation of boot.
> >
> > 7) Install shaft in car.
> >
> > Remember to replace the center bolt, circlip, spacer, and spring washer
> > with new parts.
> >
> > Does this answer your question?
> >
> > Tom
> >
> > >PS I also just had my CV boot "explode". After I cleaned up the CV
grease
> > >from my suspension ( what a mess) I got the shaft out with your
procedure
> > >( excellent by the way ) . When I took the inner piece out I noticed
> > >afterwards it is rescessed somewhat on one side. Do you know if this
side
> > >faces the car or the wheel ..Anyone else know
> .....anyone........anyone....
> > >sorry, couldn't resist the Ferris Bueller reference
> > >
> > >Clive
> >
>
> _______________________________________________
> V6-12v mailing list
> V6-12v at audifans.com
> http://www.audifans.com/mailman/listinfo/v6-12v