[V8] O2 sensor circuit, rewire from Ecu?

[7013885254]

For my 4 wire the only diff is an extra wire grounded to the chassis.

---- Original Message ----
From: "ville.hiivola at suomi24.fi" <ville.hiivola at suomi24.fi>
Date: 2/5/10 4:56 am
To: "v8 at audifans.com" <v8 at audifans.com>
Subj: [V8]  O2 sensor circuit, rewire from Ecu?
No, you're not bothering at all. I'm specially interested on this topic 
since i have had so much O2 problems on mine, so keep us posted on how 
it goes! :)

Two wires go to the ECU, pin 10 is the ground for O2 and pin 28 is the 
O2 signal.
One wire to the oxygen sensor heater relay, pin number 8/87 on the 
relay itself.
And i'm assuming one wire is grounded for the heater ground. I'm not 
sure though cause i have 3 wire sensor in mine.

Ville


>----Alkuperäinen viesti----
>Lähettäjä: chance9121 at gmail.com
>Päivämäärä: 04.02.2010 23:57
>Vastaanottaja: "V8List Fans"<v8 at audifans.com>
>Aihe: [V8] O2 sensor circuit, rewire from Ecu?
>
>Ok, ok, ok.  I've so had it with this car's bloody emissions system.  
So,
>after running around for 2-3 days, the trip computer is claiming a 
dismal
>10.5mpg average, with avg speed in the 40s, mixed highway and in town
>driving.  It also seems that I'm going through gas pretty quick.  Not 
sure
>how accurate the gauge is, but that is pretty bad.
>
>I've tried the O2 sensor 2 times now, and I'm pretty sure the wiring 
is just
>not dependable.  The first time I went in there, I found the 
connectors had
>been broken off right below the rear of the engine where the air 
cleaner an
>IM meet.  So, I had to get creative and redo all that.  I'm not 
confident
>its holding up well because of the difficulties with space causing my
>soldering to be less than optimal.
>
>So, I know I've heard mention of someone testing the circuit at the 
ecu
>connection.  And I've found a great place to route my wiring.  The 
CAT
>sensor's wiring formally resided on the passenger side footwell, 
inboard
>right by the trans tunnel, and just an inch or two inboard of the 
thick
>insulation.  I've removed this sensor and spliced the wiring together 
to
>fool the sensor, so I have that grommet free to route my wiring 
through the
>floor.
>
>So, does anyone know where I need to run my wires?  So far, I think 
that I
>would need to run from the O2 fuse in the pass foot well to the O2 
heater,
>and then one wire to ground on the chassis (on a 4 wire sensor)  and 
then I
>assume two more wires go right to the ECU, is this correct?  Anyone 
have the
>pins and maybe color/pictures?
>
>Thanks a Lot.
>Nick.
>
>P.s.  lot of traffic on the list this week, good stuff.  a bit of it 
is
>mine, hope I'm not bothering anyone with all the inquriys!
>_______________________________________________
>Audifans V8 mailing list
>Send posts to: mailto:V8 at audifans.com
>Manage your list connection: http://www.audifans.
com/mailman/listinfo/v8
>
>You can help keep the audifans site running by shopping at http:
//audifans.com/shop/
>
>


_______________________________________________
Audifans V8 mailing list
Send posts to: mailto:V8 at audifans.com
Manage your list connection: http://www.audifans.com/mailman/listinfo/v8

You can help keep the audifans site running by shopping at http://audifans.com/shop/