[Vwdiesel] Update on Grinding in front of Jetta

[Erik Lane]

Hmmm... I was sure that they were there. I just went and looked and didn't
find any.

I must have mixed up between this car and my Peugeot turbo diesel that I
drove for many years. I distinctly remember working on the freeze plug
heater and right where it was, but I thought it was on a VW.

Oops. Sorry about that. I guess you'll have to crawl around underneath.

Erik


On Wed, Nov 27, 2013 at 11:12 PM, <lbaird119 at aol.com> wrote:

>
>   Where?  There aren't any frost plugs on that side of the engine that I
> can recall.
>     Loren
>
>
>
> -----Original Message-----
> From: Erik Lane <eriklane at gmail.com>
> To: lbaird119 <lbaird119 at aol.com>
> Cc: VW Diesel Group <vwdiesel at vwfans.com>
> Sent: Wed, Nov 27, 2013 3:13 pm
> Subject: Re: [Vwdiesel] Update on Grinding in front of Jetta
>
>
> I've also seen them installed on the 'upward' side of the engine - right
> near that back of the injection pump. That might be easier to do - you'd
> probably have to pull the fuel lines, but you wouldn't be crawling around
> under the car doing it.
>
>
>
>
> On Wed, Nov 27, 2013 at 2:13 PM, <lbaird119 at aol.com> wrote:
>
>
> I did several of those at the dealer and a few since.  Seems like the
> front plug is easier to get to, or else they say to do the front and I
> always did the center, hmmm...
>   Anyway, use an air chissel and pop a light slot into the center of the
> freeze plug.  Then a hammer and screwdriver, then hammer and angle-ended
> pry bar.  Once the bar fits in the slot, pry against the edge of the hole
> and pop it out.  Sometimes goes just that easy, sometimes not but using a
> hammer and chissel tokk the whole two hours alloted.  Using the air chissel
> usually took about 45 minutes from in the door until out the door!  :-)
>   Shop didn't like us using that since we could "knock a hole in the
> block.'  Well, they're pretty resiliant cast iron plus I've yet to hit the
> block or a cylinder.  Just use short bursts once you start to break through.
>   No jacking, little hammering, just coolant dripping down your arm.
>     Loren
>
>
>
>
> -----Original Message-----
> From: dieseltdi <dieseltdi at verizon.net>
> To: vw fans <vwdiesel at vwfans.com>
> Sent: Wed, Nov 27, 2013 2:06 pm
> Subject: [Vwdiesel] Update on Grinding in front of Jetta
>
>
> Well I pulled the front spindles off of the Jetta today in preparation of
> giving
>
> hem to my son so he can take them to his work shop and press the old
> bearings
>
> ut and put the new bearings in.  My guess that it was the driver front was
> spot
>
> n.  The spindle has about ¼” of front to back wobble and almost as much
> side to
>
> ide.  The spindle is so loose in the bearing that I can almost pull it out
> by
>
> and but I could definitely do it with a few taps of a hammer and an
>
> ppropriately sized drift.  I will be gone through Sunday afternoon and I am
>
> oping to get everything back together to drive the car on Monday.  BTW I
> have
>
> ust been given a KATS block heater, the one that mounts in place of the
> center
>
> reeze plug and I was wondering how hard this would be to install with the
>
> ngine in the car.  Obviously I would have to jack the car up pretty high
> and do
>
> his from below but any other pointers?  Hayden
> “There are many men of principle in both parties in America, but there is
> no
>
> arty of principle.”
> “I do not know if the people of the United States would vote for superior
> men if
>
> hey ran for office, but there can be no doubt that such men do not run."
> “I cannot help fearing that men may reach a point where they look on every
> new
>
> heory as a danger, every innovation as a toilsome trouble, every social
> advance
>
> s a first step toward revolution, and that they may absolutely refuse to
> move
>
> t all.”  Alexis de Tocqueville
>
>
> isit my website at:  http://mysite.verizon.net/resosxp8/mydieselpages/
>
> roud owner of:
>
> 968 Beetle, my latest project, watch for details
>
> 982 VW Jetta Coupe GTD "FrankenJetta"
>
> nd many, many, many VWs; from a 1947 Beetle (13 Beetles total), to Vans (5
> - 3
>
> plit ties  2 bay window (both were campers), 1 Vanagon Westy, Rabbits (3),
>
> armen Ghia (1), Jettas (10), Passats (2), Dasher (1), New Beetle (1),
> Rabbit
>
> onvertible (1) and Rabbit Pickups (3) most now gone but not forgotten.
>
>
>
>
>
>
>
>
>
> _______________________________________________
>
> wdiesel mailing list
> wdiesel at vwfans.com
> ttp://www.audifans.com/mailman/listinfo/vwdiesel
>
>
> _______________________________________________
> Vwdiesel mailing list
> Vwdiesel at vwfans.com
> http://www.audifans.com/mailman/listinfo/vwdiesel
>
>
>
>
>
> _______________________________________________
> Vwdiesel mailing list
> Vwdiesel at vwfans.com
> http://www.audifans.com/mailman/listinfo/vwdiesel
>