Audi Boost and Engine Horsepower Graphs,
Performance info, Vehicle Weights, Component Weights
Weight/HP
info.
Vehicle Weight, 5000TQ and 1994 S4 Component Weights
Boost Graphs for 1992
Audi S4, 1991 200TQ 20V, and 1989 200TQ 10V
Horsepower/Torque
Graphs for
1998 2.8 liter V6, 5 Valve Engine,
1998 4.2 liter V8 from A8
1997 1.8 liter 5 Valve, Turbo 4 cylinder,
1992-96 S4/S6
1992-94 Audi 100 with V6,
1991 200 20V Turbo Quattro
1990-91 Audi V8 performance,
1990-91 90 Quattro and Coupe Quattro with 20V
1984-88 5000 Turbo and 5000 Turbo Quattro
1992-96 S4 and S6 performance data
1991 200 20V Turbo Quattro performance data
European S2 performance data
1992-94 Audi 100 with V6 performance data
1990-91 Audi V8 performance data
1989 200 Turbo Quattro Performance data
1990-91 90 Quattro and Coupe Quattro with 20V performance
data
1984-88 5000 Turbo and Turbo Quattro performance data
1984-87 Audi 4000 performance data
1982-85 ur-Quattro performance data
1992-96 S4 and S6 performance
- Stock S4 versus the Stock 1991 200TQ
- Horsepower:
The 1991 200TQ has 217HP @ 5700RPM, The US S4 with 227HP@ 5900 RPM
Torque:
Max Torque is 228 lb-ft (309Nm) for the 1991 200TQ, and *258lb-ft (350Nm)
for the S4.
* (Without Overboost) The S4 Engine Management system allows an "Overboost"
condition where 2.15 bar max boost is allowed for up to 15 seconds.
- The Jan. 1994 European Car Magazine indicates that the
Euro S2 which used the S4 engine, makes 230HP@5900 RPM, Max Torque of 258
lb-ft (350Nm) from 1950-3000 RPM. Interestingly, it explains the "Overboost
Torque" available is 280 lb-ft (380Nm) from 2100-4000 RPM. The Audi Factory
Brochure for the 1994 S2 also shows this overboost torque to be 380Nm @ 2100
RPM
- It would appear that the higher torque output over a
broader RPM range makes the STOCK S4 quicker in the 1/4 mile than the STOCK
1991 200TQ, even though the S4 is ~200 lbs heavier.
Keep in mind, that when you compare Stage I modified S4's versus
the Stage I modified1991 200TQ 20V, the 1991 200TQ 20V
will usually have better mid range acceleration in 3rd and 4th gear, due to
the different gearing and lower weight.
-
1991 200 20V Turbo Quattro performance
Acceleration Tests
from two
Automotive Magazines
- Zero to 30 MPH
- Zero to 40 MPH
- Zero to 50 MPH
- Zero to 60 MPH
- Zero to 70 MPH
- Zero to 80 MPH
- Zero to 90 MPH
- Zero to 100 MPH
- Zero to 110 MPH
- Zero to 120 MPH
- Zero to 130 MPH
- 1/4 Mile ET,
MPH
|
1991 200TQ 20V:
Car and Driver
5/1991
- 2.0 seconds
- 3.3
- 4.8
- 6.8
- 9.1
- 11.7
- 15.2
- 19.7
- 24.4
- 31.3
- 49.3
- 15.2 sec @90 MPH
(R &T: 15.4 sec @ 88.5 MPH)
|
1992 S4:
Road & Track 7/92,
Car and Driver 4/92
- 2.1 seconds
- 3.6
- 5.0
- 6.5 (Car & Driver 6.1)
- 9.0
- 11.3
- 14
- 17.5 (Car & Driver 17.5)
- n/a
- (Car & Driver 29.4 )
- n/a
- 15.0 sec @93 MPH
(C&D: 14.9 sec @94 MPH)
|
European S2 performance
- R&T Jan. 1991, Stock European S2 at 3130 lbs,
with 220HP to have a 1/4 ET of 14.6 sec at 96.5MPH
- European Car 6/95. MTM Modified 1994 Euro S2 with
a reported 428 HP at 6400 RPM,
358 lb-ft torque at 2600RPM, 0-60 MPH 3.9 sec, 0-100MPH, 9.0 seconds,
35-100 MPH in 4th gear (6 speed) in 10.9 sec, Top speed 168 MPH.
1992-94 Audi 100 with V6 performance
- Car and Driver Dec. 1991, 1992 Audi 100CS, 5 Speed,
Front Wheel Drive,0-60 MPH 8.4 sec, 1/4 mile ET, 16.5 sec @85 MPH,
Top Speed 135MPH, curb weight 3389lbs, 172 HP @5500RPM, 184 lb-ft @3000RPM,
6400 RPM Redline.
1990-91 Audi V8 performance
1989 200 Turbo Quattro Performance
Dual knock sensor MC 10V Turbo 5 cylinder, 8:4 to 1 compression
ratio, K24 Turbo, 110,000 miles, ECU modifications which provide 11-12psi boost,
single pass intercooler from 1991 200TQ 20V, all other engine and fuel system
components are stock, stock exhaust system, catalytic convertor test pipe installed
during the 1/4 mile test, Best ET, 14.75 seconds at 92.3 MPH.
1990-91 90 Quattro and Coupe Quattro with
20V
- VW & Porsche magazine June 1990, Coupe 20V, 162HP@
6000RPM, 157 lb-ft @ 4500 RPM, curb weight 3171 lbs, 0-60MPH, 8.1 seconds,
Top speed 135MPH.
- 1990 Audi 90 Quattro 20V, Sean Douglas,Naturally
aspirated, Using the G-Tech Pro, 0-60 9.39 s,
1/4 mile 16.69 s trap speed 88.9 mph, G-Tech measured wheel HP 143.
- 1990 CoupeQ 20V, Owned by R. Lagemann, using G-Tech
Pro, 0-60 7.7 seconds, Mods: Cone filter, Exhaust, cams, and no A/C.
- VW & Porsche, June 1990, Abt Coupe 20V with 2.5 liter
engine,
200HP @6100 RPM, 162 lb-ft at 4000RPM, 0-60MPH 7.0 seconds.
1984-88 5000 Turbo and Turbo Quattro performance
- 1987 5000TQ Track Car: It was put on a serious diet
and lost 450 lbs. It now weighs about 2900 lbs with 1/2 tank of fuel but
without the driver. Engine and transmission are stock with 125k miles, Stock
intercooler, stock K26 turbo, stock air filter, stock fuel injection, stock
exhaust downpipe etc. Only modifications include a 2 1/2 inch exhaust system
with single muffler and a Custom ECU with 2.5 bar pressure sensor and modified
fuel and boost maps to produce 2.1 bar (16psi).
PIR Dragstrip testing: 5-25-2001
The 60 ft time was 1.889 seconds,
1/8 mile ET was 8.831 seconds.
1/4 mile Elapsed Time (ET) was 13.877 seconds @
98.472 MPH.
During this test, the ambient air temp was 80 degrees F, altitude was ~200ft,
Late afternoon, early evening.
Car with fuel and driver weighed 3100lbs. Center diff was locked during these
1/4 mile acceleration tests.
PIR Dragstrip testing: 9-20-2002
Same 1987 5000TQ track car as described above,
only the car had a stock K24 turbo installed along with the 20V Intercooler.
60 foot Elapsed Time (ET) was 1.838 seconds
330 foot ET 5.623 seconds
1/8 Mile ET 8.795 seconds @ 77.76 mph
1000 foot ET 11.551 seconds seconds
1/4 mile ET 13.895 @ 96.24 MPH
Ambient air temp was 60-65 degrees, testing done during late evening ~11PM
- R&T 8/85, 1986 5000S Turbo Quattro, 0-60 MPH 8.3
sec, 1/4 mile ET 16.4 @85.0 MPH,
C&D 8/85, 1986 5000 Turbo Quattro, curb weight 3342, 0-60MPH 8.2 sec,
1/4 mile 16.1 sec @84 MPH, Top speed 139MPH.
- European Car August '85, 1986
5000S Turbo Quattro,
Curb weight 3351lbs, 0-50MPH: 5.7 sec, 0-60MPH: 8.0 sec
- European Car April '87, 1987
5000CS TURBO FWD
Curb weight 3086 lbs, 0-30MPH:3.3 sec, 0-60MPH: 8.7sec
- 1984 5000 Turbo, 3 speed
Automatic, FWD, 8:3 to 1 compression, 140HP @5500RPM, 149 lb-ft @2500 RPM,
0-60 10.34 sec, 1/4 mile ET 17.5 sec @81MPH, curb weight 3042lbs, top speed
124MPH,
(Euro version has 8:8 to 1 compression, 8psi boost, 182HP, 143MPH top speed)
1984-87
Audi 4000 performance
- R&T March 84, 1984 4000Q, Curb Weight 2820lbs,
0-60MPH 10.2 sec, 1/4 mile ET 17.3@76MPH, 115 HP @5500 RPM
1982-85 ur-Quattro performance
ur-Quattro
- C&D June 1982, 1983 ur-Quattro, Curb weight 3040lbs,
0-60 7.8 sec, 1/4 mile ET 15.8 sec @ 86 MPH, 2144cc, 160HP @5500 RPM, 170lb-ft
@3000RPM, 12.3 psi max boost
Weight/HP
info
Vehicle Weight/Horsepower:
Assume a curb weight (no driver) of 3850 lbs for the
US S4 with 227HP and 3650 lbs for the 1991 200TQ 20V
- The 1991 200TQ is at 16.82 lbs/HP
- The S4 is at 16.96 lbs/HP
- The 1986-90 5000TQ/200TQ at 3450lbs would only need 205HP
to be at the same lb/HP rating.
- The 1995 BMW M3 at 3150lbs with 240HP comes in at 13.1
lbs/HP.
- The S4 needs 293HP to meet the M3 weight/HP,
the 200TQ 20V needs 278HP,
the 5000/200TQ needs 263HP.
- Automobile Magazine Oct. 1987, Porsche 959, 450HP, curb
weight 2977, how does 6.6 lbs/HP sound....
Hmm....Looks like I need to go on a diet.....
Vehicle Weights, S4 and 5000TQ Component
weights
Horsepower is often used to compare vehicles performance,
often times unfortunately, the weight of the vehicle is overlooked or not mentioned.
The transmission gearing and tire size, will also have a large affect on the
acceleration capability of the vehicle. The other aspect of performance, is
the amount of torque the engine produces at different RPM points, if you were
to graph the torque output vs RPM, this area under the curve, is usually more
important to gauge acceleration potential, than one HP number at a single RPM.
- AAN Engine code 5 cylinder Engine
Block with Pistons, rods, crankshaft, Oil pump assembly, oil pickup and oil
pan, but without the following: oil filter housing, crank damper pulley and
flywheel. 192 lbs
- Bare engine block without the
following: No crankshaft, rods, pistons, oil pump or rear seal flange 118
lbs
- Crankshaft 44 lbs
- 5 pistons with 5 rods ~13 lbs
- Oil Pump assembly and rear seal
flange 5 lbs
- Oil Pan, pickup and windage tray
12 lbs
- Front Crank damper pulley 11
lbs
- Dual mass Flywheel 27 lbs
- Complete Cylinder head with valves, 2 camshafts, intake
manifold, fuel injectors, exhaust manifold 100
lbs
- Turbocharger 15 lbs
- Exhaust Downpipe 14.5 lbs
- A/C Compressor 17.5 lbs
- Alternator 16 lbs
- Turbocharger crossover pipe 4 lbs
- Intercooler with mounting brackets 11.5 lbs
- 01E 5 speed Transmission with shift linkage and Procon
Ten cable guide 159 lbs
- Rear Differential with differential lock 73 lbs
- Rear suspension, including subframe, trailing arms, rear
hubs, spindles, differential, differential lock and 2 axles/4 CV's, (does
not include shocks/struts/springs/upper-shock-mount) 192 lbs
- Front to rear Driveshaft 25 lbs
- 2 rear axles with inner and outer CV's 29 lbs
- Rear strut, spring, upper shock mount 15 lbs
- 16X8 five spoke forged alloy
wheel 18lbs
- 16 X 8 five spoke wheel with 225/50X16 Dunlop SP 4000
Tire 46 lbs
- Front Sway bar with 2 bushings
15 lbs
- Left Front Strut with coil spring, upper strut mount,
strut bearing 43 lbs
- Left front Lower control arm
6 lbs
- Front Subframe with 4 subframe bushings
27 lbs
- Steering shaft with adjustable column mount
14 lbs
- Shifter and shift linkage
5 lbs
- Front Brake rotor and G60 caliper and brake line
31 lbs
- G60 Brake Caliper and brake line
16 lbs
- Front Brake rotor 15-16
lbs
- Front shock and coil spring
14 lbs
- 2 Rear Brake Calipers 17
lbs
- L/F Strut housing with wheel hub and wheel bearing
22 lbs
- Dual exhaust system with dual catalytic convertors, includes
center resonator, rear muffler 107 lbs
- 2 Catalytic convertors 25
lbs
- Power Steering pump with mounting bracket with belt tensioner
13.5 lbs
- Power Steering pump without pulley
6 lbs
- ABS Hydraulic Assembly 11
lbs
- Brake Hydraulic Booster
3 lbs
- Brake Master Cylinder 2
lbs
- Brake Accumulator (bomb)and mounting bracket 4.5
lbs
- Emergency brake handle and cable guide 2.5 lbs
- Front hood sheetmetal, without grill, without hinges
or hood shock 51 lbs
- L/F Fender 9 lbs
- Rear Trunk lid with hinges/shocks without tail light
lenses 41 lbs
- Rear Bumper with cover 27 lbs
- Drivers Seat with armrest,
sport version black leather
67 lbs
- Passenger front seat, sport version black leather
60 lbs
- Rear seat bottom, sport version black leather
20 lbs
- Rear Seat back with center arm rest, sport version black
leather 20 lbs
- Left Rear View Mirror complete
2.5 lbs
- Right Rear View Mirror complete
2 lbs
- Left front door sheetmetal skin with hinges 34 lbs
- Left front door aluminum frame with glass and electric
motor 22 lbs
- Left front door panel with Bose speaker without handles
trim 12 lbs
- Left front door complete 70 lbs
- Left rear door complete
~50 lbs
- Left rear door sheetmetal skin with hinges 27 lbs
- Left rear door aluminum frame with glass and electric
motor 18 lbs
- Left rear door glass 7 lbs
- Pedal Assembly with clutch master
8 lbs
- Sunroof glass panel with sunshade 21 lbs
- Sunroof metal support frame with guide cables, wind/rain
deflector and motor 29 lbs
- Headliner 5 lbs
- Misc. Body hardware, nuts and bolts 22 lbs
- Vehicle wiring harnesses except ECU harness with battery
cables 54 lbs
- Seat Heater wiring harness
3 lbs
- Power Window and mirror harness
7 lbs
- Windshield wiper motor and arm
assembly 7 lbs
- Headlamp assembly
7 lbs
- A/C Evaporator housing with evaporator
11.5 lbs
- Heater box with blower 15.5
lbs
- Procon Ten cables and guides including
front seat belt retractors 13
lbs
- Empty Gas Tank with fuel pump and fuel sending unit
40 lbs
- Bare Body with front windshield and
rear window, dashboard, and front hood, otherwise it is stripped clean without
the following items: drivetrain, the front and rear suspension, the 4 doors,
both fenders, rear trunk lid, no wiring, no interior, no carpet, no headliner,
no sunroof assembly.. 850 lbs
Weight in US
pounds of the individual components from a 1987 5000TQ. Some of these items
were removed from my 1987 5000TQ track car to get the weight down. Car now
weighs about 2825lbs with no fuel, no driver, and no spare tire/tools.
- Fuchs 15 X 6 five spoke forged alloy wheel with 205/60
X 15 Dunlop D60 tire 37 lbs
- TSW Aftermarket "Blade" style 5 spoke alloy
wheel with Michelin Pilot 205/55 X16 tire 42 lbs
- Door Panel with stereo speakers 10 lbs
- Front and Rear Carpet (no padding) 25
lbs
- Rear Window motor and regulator 3
lbs
- Front Seat, Leather, 10 way electric 60
lbs
- Rear Seat bottom and back 39 lbs
- Power Seat and Window wiring harness and Relays 10
lbs
- Sunroof motor and rails 10 lbs
- Sunroof sheetmetal roof 10 lbs
- Front Windshield Glass without trim
32 lbs
- Exhaust system after the cat 54
lbs
- Rad Fan and shroud 11 lbs
- Plastic/Aluminum Radiator (Empty) 16
lbs
- A/C Compressor, brackets, hoses, bolts and complete
evaporator housing 65 lbs
- Power Steering pump, bomb, hoses, bracket, fluid 22
lbs
- OEM Hydraulic Brake Assist unit 5
lbs
- Hydraulic Steering rack 22 lbs
- ABS Hydraulic Controller 11 lbs
- CIS Air box and Fuel distributor and fuel injectors/lines
19 lbs
- Alternator and adj bracket 16 lbs
- Turbocharger (water cooled) 14 lbs
- Exhaust Manifold, Waste Gate, and WG pipe 23
lbs
- Intake Manifold w/o ISV 13 lbs
- MC Cylinder Head with Intake and exhaust 75
lbs
- Front Bumper and cover 21 lbs
- Rear gas tank shield 8 lbs
- Cross support piece for exhaust and driveshaft 4
Engine Horsepower and Torque graphs courtesy
of Audi AG, all rights reserved.
Copyright © SJM Autotechnik
Return to SJM Autotechnik main page.
|